what happens when ac supply is given to D.C motor.
Answers were Sorted based on User's Feedback
Answer / pandi
if A.c supply given to D.c motor more spark at brush & run
at low speed with noise
| Is This Answer Correct ? | 24 Yes | 4 No |
Answer / chandan
It depends on the motor construction. If the field winding
is connected in series with the armature winding, the motor
is like a universal motor and will probably operate
normally. If the field winding is connected in parallel with
the armature, the motor will not run, but will draw current,
make noise and get hot.
| Is This Answer Correct ? | 20 Yes | 0 No |
Answer / empobart jhambt baski
I want to know what is exactly the answer of this question?
| Is This Answer Correct ? | 20 Yes | 3 No |
Answer / arockia doss
Its quite simple...
Motor Will run with reduce speed & With Humming noise Comes
with Steps of jerk.
| Is This Answer Correct ? | 10 Yes | 1 No |
Answer / vinaykumar
it will run at very low speed and excessive heat is
produced in the motor due high hysterisis and eddy current
losses and along run may damage the motor
| Is This Answer Correct ? | 10 Yes | 2 No |
Answer / pradeep kumar rawat
When ac supply is ginen to DC motor, DC motor will run with
less speed and prodeced some noice.
| Is This Answer Correct ? | 24 Yes | 18 No |
Answer / mr.anant ram yadav
if A.c. supply given to D.c. motor the net torqe will be
zero and motor will not work. bez postive &negative cycle
is zero.
| Is This Answer Correct ? | 19 Yes | 14 No |
Answer / manish
dc motor does no work on ac.it will not rotate because in
india ac frequency is 50 hz so the time of half cycle is
only 10 ms.this time is too short to move because of its
inertia.
but expeptionaly dc series motor will rotate when it is
given to ac supply.
| Is This Answer Correct ? | 5 Yes | 1 No |
Answer / swarupa
In ac supply the magnitude and direction of voltage or
current changes for every half cycles so the dc motor may run
but in very low speed due to less torque develop & also due
to inertia.If it is run continue the frequency losses may
increase due to high heat.The efficiency poor.
| Is This Answer Correct ? | 2 Yes | 0 No |
Which type of Oil is used in transformers, & what is its strength?
basic priniciple of induction motor
Name different types of circuit breakers and their voltage ratings?
Why DC weldings sets preffered over AC considering human safety aspects ?
what is the cost of a analog tachometer, for lab purpose/
Wghat is D-curve MCBs
how to calculate the battery Ah? what is the formula.
what is the formular for the calculation of CT'S when installed as part of a electrical installation so the correct meter is used
Comparing to AC transmission, corona & R in DC transmission is……. a) lower b) higher c) same
Earth Is a very good conductor or very good insulator.? If a good conductor then why current donot flow through small piece f earth and if a good insulator then why we use it as return path in lines.???
what is difference b/t ac current and dc current
4 Answers L&T, Meghana Engineers,
what was the function of the auxillary relay?
Civil Engineering (5086)
Mechanical Engineering (4456)
Electrical Engineering (16639)
Electronics Communications (3918)
Chemical Engineering (1095)
Aeronautical Engineering (239)
Bio Engineering (96)
Metallurgy (361)
Industrial Engineering (259)
Instrumentation (3014)
Automobile Engineering (332)
Mechatronics Engineering (97)
Marine Engineering (124)
Power Plant Engineering (172)
Textile Engineering (575)
Production Engineering (25)
Satellite Systems Engineering (106)
Engineering AllOther (1379)