WHAT IS THIS INSTRUMENTATION?
Answers were Sorted based on User's Feedback
Answer / leo dominic
Instrumentation deals with study and implementation of measuring and controlling parameters in a system to achieve the desired output.
Is This Answer Correct ? | 16 Yes | 0 No |
Answer / sushil jambhulkar
Inst'n is the study of inst, inst which r use to to sense,to measure,to control the the physical (non measurable) parameters.
Is This Answer Correct ? | 4 Yes | 2 No |
Answer / arvind kumar
Instrumentation engineering is a branch of science which
deals with measurement, display and control and serves all
other branches of engineering like industrial process
instrumentation, biomedical instrumentation, analytical
instrumentation.
Measurement is also a broad field. varieties of measuring
sensors are available for different process variables(i.e.
pressure, flow, D.P. etc) such as bourdan tube,
thermocouples etc.
Display gone much more advancement like CRT replaced with
TFT, analog meters to digital meters etc.
The most innovative application of control in last decades
are automation.
like DCS, PLC, LIFE JACKETS.
Is This Answer Correct ? | 1 Yes | 1 No |
Answer / jainul
measurment of process varible like
temp,press,flow,level,etc.. ,then calibration and controll
it is instrumentation simple answer for instrumentation
Is This Answer Correct ? | 0 Yes | 0 No |
INSTRUMENTATION IS ANY PROCESS DATA OF MEASUREMENT,INDICATION,RECORDING,CONTROLLING AND MONITORING OF ANY PLANT AND INDUSTRY.
Is This Answer Correct ? | 0 Yes | 0 No |
Answer / pradeepkumar.r
Instrument is a technique at which is used to quantifying and qualifying by using the measurements.
Is This Answer Correct ? | 0 Yes | 0 No |
Answer / harichy20
INSTRUMENTATION IS PROCESS VARIABLE CONTROLLED.
Is This Answer Correct ? | 4 Yes | 5 No |
How does a single acting, spring return ball valve actually work? Does it require continuous air supply?
0 Answers Process Control Technologies,
sir, i preparing hpcl,ongc,barc,hal exams(instrumentation engg)pls send a placement papers
what is sil (safety integrity level
in any transimitter (flow/level) there are three terminals for supply& test (+,-,+)in two wire,24VDC given to Tx.,but how 4-20 ma signal travels thru same wire (as it is for 24VDC input supply)?
(1) In turbine, what does term CDP, NI, NH, HSSOC, means. (2) What is the purpose of LO overhead tank in turbines.(3) An equipment is certified for EEX, IA, IIC,T6, what do you under stand by this.(4) what is SURGE, and how it is prevented, what is the purpose of bypass valve across AS valve.(5) Give 2 application of quartz crystal used for process parameter measurement.(6) what is meant by cold float of compressor shaft. (7) state four different types of flow measurement. For gas flow measurement mmscfd is the common unit. Expand the unit and specify significance of word S in the unit.(8) what is meant by Gap voltage, in vibration measurement. Normally how much Gap voltage is set and state the reason.(9) what will the new flow factor if D/P transmitter is Re-Ranged from 25” wc to 50” wc.(10) what is the usage of QDV & Volume booster.
what is the use of glycol filling in seal pot (or) condensate pot in instrument impluse line?
what difeerent between HART and BRAIN?
In closed loop control there are several “blocks” used to show the interactions between the process and the control system. These blocks are referred to as the “process” and the “controller.” Describe the relationship between these two blocks when creating a well tuned control loop.
what is bevel? why bevel required in orifice plate?
what is the difference between PLC & DCS
sir,would you please send me the Hindustan petroleum corporation limited papers(HPCL).my e-mail ID is ujjwal_sharma1983@yahoo.com
How we are blocking 40 kg or more pressure through only 6 kg instrument air in control valve