working of a diesel generator.




Answers were Sorted based on User's Feedback



Answer / guest

by using a diesel operated motor the mechanical input to
the generator is given and the generator generates the
electricity

Is This Answer Correct ?    436 Yes 86 No

Answer / manoj sharma

A diesel generator is the set of diesel engine and
alternator. Disel engine is prime mover which rotates the
alternator and alternator generates the electricity.
Further diesel engine works on principle of carnot cycle,
air is compressed in a cylender, then it is compressed up
to high pressure, disel is injected to this compressed air
thus cumbustion takes place,this energy force to move the
piston in the cylendrical passage, piston is further
connected to crank shaft. on the other hand generator
wotrks on principle of electo magnetic induction, when a
DC excited rotor is rotated then at synchonous speed EMF
induced in static armature.

Is This Answer Correct ?    243 Yes 24 No

Answer / apurb prakash

Diesel is used as fuel for the generator.disel prodused
mechanical energy with the internal construction of
generator.then this mechanical energy is converted into
electrical energy

Is This Answer Correct ?    211 Yes 41 No




Answer / vijay

genrator is a machine which use diesel as fuel to run the
engine which rotate the rotor of an altenator which produse
the electricity.

Basically genrator is a machine which convert the machnical
energy into electrical energy.

Is This Answer Correct ?    149 Yes 27 No

Answer / sachin subhash pawar

diesel generator worked as principle of faraday's law of
electromagnetic effect.mechanical energy is converted to
electrical energy.It can stared to d.c supply i.e. 12v ,
24v.D.C supply to starter and after starting it produce
A.C. supply.Engine only use as a prime mover.

Is This Answer Correct ?    103 Yes 31 No

Answer / kumar

AS PER MY FIELD EXPERIENCE .IN DG SET DIESEL IS USED FOR
FUEL OF STROKE ENGINE,SO THE ENGINE PRODUCED MECHANICAL
ENERGY .THE SHAFT OF ENGINE IS COUPLING WITH GENERATOR
THEREFORE MECHANICAL ENERGY CONVERTED INTO ELECTRICAL
ENERGY .BY USING GOVERNOR WE CAN ADJUST THE SPEED OF THE
ENGINE .&WE CAN DEVELOPING OR CONTROLLING THE DG OUTPUT
VOLTAGE BY USING AVR(AUTOMATIC VOLTAGE REGULATOR).THE
CONTROLLING & DISPLAYING OF GEN SET IS OPERATING BY DC
VOLTAGE FROM BATTERY .WE CAN CHARGE THE BATTERY AT THE TIME
OF ENGINE RUNNING BY USING THE CHARGING ALTERNATOR.ITS
COUPLED WITH ENGINE SHAFT THROUGH BELT .FOR THE SAFE WE
USING STARTER MOTOR TO START ENGINE THATS MOTOR OPERATED BY
DC VOLTAGE .

Is This Answer Correct ?    71 Yes 9 No

Answer / p.viswanath rao

Diesel Generator is a set of engine and alternator.
(Which converts mechanical energy in to electrical energy)
here engine is using for rotating the shaft(prim mover or
crank shaft).
Rotation takes place as fallows:
1)The pistons placed in cylinders and these pistons are
connected to Crank shaft through connecting rads
2)By using diesel as a fuel the blasting takes place in
cylinders, this blasting energy can be converted in to
rotation through piston,connecting and crank shaft
3)this rotor speed strength(should be synchronous
speed)depends on firing order of the cylinders (of course on
number of poles on rotor)
4)this shaft is connected to Alternator rotor
5)this rotor contains poles, this rotor will get the D.C
supply from A.V.R through Exciter (RRA: Rotating Rectifier
assembly, it is a converter bridge)
6)So with rotor(poles) rotation the EMF will induce in main
Stator(Faraday's law of electro magnetic effect)
7)A.V.R out put depends on load effect on D.G.
((for further full detail call me at 09458490849)

Is This Answer Correct ?    53 Yes 5 No

Answer / aayush

A diesel generator works on the principal of Faraday's law
of electromagnetic effect. Mechanical power of the rotor is
converted into electrical power. As the rotor rotates
(because of the external voltage given to it through the
battery), EMF and hence current is generated, which is
collected by collectors connected on the stator.

Is This Answer Correct ?    67 Yes 22 No

Answer / v.dhamodharan

generator is a mechanical convert electrical it is a multi
purpose used generator
tower section mainly used generator .
EB power off generator used gen is absent tower is down

Is This Answer Correct ?    73 Yes 39 No

Answer / gagan deep singh

Generator: IT IS A MECHANICAL DEVICE WHICH IS USED FOR
CONVERTING THE CHEMICAL ENERGY STORED IN FUEL TO THE
ELECTRICAL ENERGY. IT CONSISTS OF FOLLOWING COMPONENTS
1.DIESEL ENGINE
2.TURBINE
3.ALTERNATOR
4.COIL WITH PRIMARY $ SECONDARY WINDING OF COPPER WIRE.

1.DISEL ENGINE CONVERTS CHEMICAL ENERGY INTO MECHANICAL
WORK.
2.TURBINE CONNECTED WITH CRANSKHAFT OF ENGINE ROTATES
IN THE CORE(STATOR.
3.ALTERNETOR CONVERTS MECHANICAL ENERGY INTO ELECTRICAL
ENERGY.
4.WINDINGS ARE USED TO STEP UP OR STEP DOWN THE VOLTAGE.

Is This Answer Correct ?    56 Yes 23 No

Post New Answer



More Electrical Engineering Interview Questions

what will be fault level of 11 KV , 2000 A ELECTRICAL SYSTEM?

4 Answers  


how to flameproof electrical motor on the shaft?

0 Answers  


could anyone suggest project title

1 Answers   Engineering,


explain safety measures in alternator?

0 Answers  


what is the relation between size of the anteena and wavelenghth of radiated wave

0 Answers  


Why Transistors are not used as switching devices?

15 Answers  


why we use bare wire in high tension power instead of using insulated wire?

2 Answers  


Why is better to have a minimum ceiling voltage of 250% than 160%?

0 Answers  


How calculate the MTA in relay?

0 Answers   Unicharm,


I am completed DEEE in tamilnadu, now i am working in andhrapradesh with 2.5 year experience in relavent field. capacity of the tranformer is 11KV, 1MVA Transformer, i am eligible for getting c licence in andhrapradesh pl help me.

0 Answers  


what are the types used for alternator earthing,what will happen if more than two alternator is working in parallel with each having own system earthing.is there any possibility for circulating current in between two system.

3 Answers   BEL,


A mass of 1200g is accelerated at 200 cm/s2by a force. The value of the force required is:(a) 2.4N(b) 2400N(c) 240 kN(d) 0.24N

0 Answers  




Categories
  • Civil Engineering (4468)
  • Mechanical Engineering (3651)
  • Electrical Engineering (15446)
  • Electronics Communications (2613)
  • Chemical Engineering (651)
  • Aeronautical Engineering (78)
  • Bio Engineering (30)
  • Metallurgy (95)
  • Industrial Engineering (191)
  • Instrumentation (2832)
  • Automobile Engineering (134)
  • Mechatronics Engineering (40)
  • Marine Engineering (59)
  • Power Plant Engineering (160)
  • Engineering AllOther (1313)