All industrial (power plant,
sugar. Cement etc...) chimneys
are circular in shape rather
than any other shapes...
Y..?
- 9 Answers
- 17301 Views
- BPCL Bharat Petroleum, UltraTech, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / ameet
1) Eaisy in construction
2) Less leakages
3) Circular Profile provides less resistance to air flow
| Is This Answer Correct ? | 48 Yes | 7 No |
Answer / bejoyed
adding to answer#1
i would like to mention that,a circle encircles more area
than any other shape with a given length of material.. in
the same way a cylindrical piping can carry more fluid with
least material of construction...
also the flow of any fluid finds minimum resistance across a
cylindrical piping than any other shaped ones...
| Is This Answer Correct ? | 18 Yes | 3 No |
Answer / franco ambrose s
1.air flow area would be more compare to anyother shapes
2.Resistance of air flow is very less
3.area is more so temperature as well as pressure would be
reduced
4.finally construction is easy compare to other shapes
| Is This Answer Correct ? | 6 Yes | 3 No |
Answer / rkr
Benifits of circle:-
A> Surface area to volume inside ratio is important.Surface
area related to manufaturing cost, and volume is amount of
gas delivered.
B> resisitance in flow of gas will be good.
| Is This Answer Correct ? | 4 Yes | 2 No |
Answer / gaurang
Circular shape universal. It is easy to construct as well
as can have advantages from the maintanance point of view.
Also it is easy to establish.
| Is This Answer Correct ? | 3 Yes | 2 No |
Answer / santosh raikar
flow is uniform in all cross sectional area
| Is This Answer Correct ? | 3 Yes | 5 No |
Answer / guest
because easy to construct&the pollution is not more harmfull
for other cross section shape of chimny
| Is This Answer Correct ? | 2 Yes | 7 No |
HOW IS FATIGUE DIFFERENT FROM STATIC LOADING??
Dear sir, I am student of mechanical engg.Please,send me reliance energy placement papers.
Why tyres are manufactured in black colour?
22 Answers MRF, TVS,
What is difference between Higher calorific value and lower calorific value?
Suppose there are two vessels. One of diameter = D and other vessel dia = d. Suppose in vessel with dia D, water is filled upto height H and vessel with dia d is empty. Now both vessels are connected.Water will flow from D dia vesel to small d dia vessel.Suppose after equilibrium height of water in vessel with dia D is h. How much is h in terms of D, d,H etc?
WHICH ONE IS PREFERRED, VERTICAL OR HORIZONTAL PUMP WITH COMPLETE TECHNICAL DETAILS
AFTER OVERHAULING KTA19G3 AND JUST ABOUT TO START ,BUT WE DIDNT FIX THE OIL SUMP AND TEST FOR -WATER LEAK FROM LINER O RING SIDE,THEN WE FILLED WATER AND FOUND WATER LEAK FROM INSIDE OF ENGINE -CAM FOLLOWER SIDE PLEASE GIVE ADVICE TO RECTIFY THE SAME
What is a steam turbine diaphragm?
HOW WE CALCULATE THE WELDING IN JOB.
can a horizontal mount motor be used vertically?
How to convert GSS duct volume in KG for all guages
how can I calculate daya of pump
-
Civil Engineering (5085) - Mechanical Engineering (4451)
- Electrical Engineering (16632)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
