sigal phase supply is 230 v ac two phase supply is 415 v ac
then why three phase supply having supply is 415 v ac why
not 690v ac

Answers were Sorted based on User's Feedback



sigal phase supply is 230 v ac two phase supply is 415 v ac then why three phase supply having sup..

Answer / neeraj pandey

voltage value is the Line to Line Voltage. Line to line
voltage is the voltage between any two phase lines.
In single phase there is one phase and another is earth wire
and voltage between them is 230V approx.
In two phase the line voltage is 1.732 times of the single
phase voltage and the value is 415 V approx.

In three phase system the value of voltage between two
phases are taken which is same as two phase system.

if we take the voltage diff between all three phases it will
be ZERO..

Is This Answer Correct ?    11 Yes 0 No

sigal phase supply is 230 v ac two phase supply is 415 v ac then why three phase supply having sup..

Answer / pillay

Single phase voltage is 240 volts and two
or three phase voltage is 415v because
the voltages are actually spaced 120 degrees
in between them in a cycle .Further more you
measure the potential difference in between
any of them.

Is This Answer Correct ?    2 Yes 1 No

Post New Answer

More Electrical Engineering Interview Questions

How can we measure and monitor critical performance parameters of Diesel Generator Sets, both electrical and engine ?

3 Answers   Cologicx Systems,


what is the difference between id fans and fd fans

12 Answers   Perkins Thermal Systems,


Hi, I'm going to attend BHEL interview for exexutive trainee (ET ) on 22nd DEC . Till now if anyone attended the interview pls help me out regarding the interview. I'm an electrical engineer

3 Answers   Bhel,


what is the principle of generator , induction motor,d.c motor

1 Answers  


What is the difference between type1 and type2 relay protection co-ordination for motor feeders

0 Answers   DAE,






what composit error,ratio error,phase error in CT and PT??

4 Answers  


Alternator rotor earth fault relay circuit

0 Answers  


Our Company's Contract Demand is 110 kVA. We use 12 Capacitors each of 12.5 kVAr Capacity to maintain Power Factor of 0.99. So, what steps should we take so that our Contract demand does not exceed 110 kVA?

1 Answers   Jindal,


What is electrical earthing?

1 Answers  


When a single pase capacitor run motor- run on 230vac and Case(1)run with 8 Mfd 250 vac.capacitor , Case( 2) run with 8 Mfd 400vac capacitor. What is difference between both case regarding power ,efficiency etc?

0 Answers  


why rating of transformer is in kva instead of kw?

3 Answers  


the power consumption of perminant magnet moving coil?

1 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)