Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


Can we use pure oxygen in IC engines instead of air??

what would be the advantages and disadvantages of using it??

Have any steps been taken about this??



Can we use pure oxygen in IC engines instead of air?? what would be the advantages and disadvanta..

Answer / sornakumar

Highly concentrated sources of oxygen promote rapid
combustion and therefore are fire and explosion hazards in
the presence of fuels.
The fire that killed the Apollo 1 crew on a test launchpad
spread so rapidly because the pure oxygen atmosphere was at
normal atmospheric pressure instead of the one third
pressure that would be used during an actual launch.

Is This Answer Correct ?    8 Yes 1 No

Post New Answer

More Mechanical Engineering Interview Questions

what is the viscosity of hydraulic oil?

1 Answers   ONGC,


What causes crankcase explosion?

0 Answers   Bhel,


why we r recommended for pre-action sprinklers @ generator/tx/mv panel room. If any leakage there,that panel will damage. So what is the Logic for pre-action sprinklers there?

0 Answers   DOW,


WHAT IS THE UNIT OF ROUGHNESS

1 Answers  


if silica is removed from DM Plant completely from where the silica come in Boiler Drum

9 Answers   BARC, SSA,


In a rankine cycle if maximum steam pressure is increased keeping steam temperature and condenser pressure same, what will happen to dryness fraction of steam after expansion ?

0 Answers  


Which is the common element between brass and bronze ?

0 Answers  


Distinguish between creep and fatigue.

0 Answers  


Hiii...I am from instrumentation dept in last plant and now in new plant management transferrd me to turbine dcs operation...how and which way I can prepare for dcs operation...time is just 1 month...???

0 Answers  


what is procedure of measuring operating length of mechanical seal . (in case of centrifugal pump)

0 Answers  


why we have to know the specific frequency of any equipment? does anybody know about specific frequency ?

3 Answers   ISRO,


Which welding process uses non-consumable electrodes?

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4456)
  • Electrical Engineering Interview Questions Electrical Engineering (16639)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)