why rotor winding in induction motor is not earthed.
normally we uses star winding in rotor .why?

Answers were Sorted based on User's Feedback



why rotor winding in induction motor is not earthed. normally we uses star winding in rotor .why?..

Answer / sugun_eee

In Induction motor rotor, each phase winding will be
identical and equivalent in parameters. Hence for balance
star connection there will not be any(circulating) nuetral
current at star point. there by............

Is This Answer Correct ?    9 Yes 3 No

why rotor winding in induction motor is not earthed. normally we uses star winding in rotor .why?..

Answer / sugun_eee

DEAR
YOUR REPLY ITSELF STATING "IN CASE OF FAULT" AND ALSO NO
EXERNAL FORCES WILL CAUSE TO DAMAGE THE ROTOR CKT. UNTILL
UNLESS INSULATION FAILURE FOR THE ROTOR WINDING. HENCE IF
THE ROTOR IS HEALTHY IT WON'T BE EARTHED. AS UR STATEMENT
IT WILL CREATES HEAVY VIBRATIONS AND COUSES MOREHEATING OF
THE STATOR.

Is This Answer Correct ?    3 Yes 1 No

why rotor winding in induction motor is not earthed. normally we uses star winding in rotor .why?..

Answer / harendra

but in case of fault , there will be unbalance so i think
neutral should be grounded.

Is This Answer Correct ?    0 Yes 7 No

Post New Answer

More Electrical Engineering Interview Questions

Why all transmission lines are AC, not DC line?

4 Answers  


If 11 KV breaker on the primary side of a 11 KV/3.3 KV 12.5 MVA transformer can be installed at a distance of 1000 mtrs through a 11 KV cable. If no what are the probable reasons.

1 Answers  


what is the formula to convert from KVAr to current?

1 Answers   Halcrow International Partnership,


star delta connection used in reduce the starting current at 3 times . how its reduce the current please explian .

7 Answers   HP,


Why insulation layer of a High Voltage cable is more than a current carrying cable?

3 Answers  






I'm looking for a mnaual set for a Teradyne J750. Softcopy would be preferred but I'll take what I can get.

0 Answers  


what is the effect of change in supply frequency on load angle of synchronous motor,all other parameters remaining same?

0 Answers  


what is the knee point voltage in current transformer

2 Answers  


What is the main feature of v/f control?

1 Answers  


what is a core company? why should we join a core company?

1 Answers  


how circuit breaker work.. what is the operations taking place inside a circuit breaker when an overcurrent occurs... is it similar to fuse?

0 Answers   LTT,


Tell me harmfull effects of over voltage,under voltage,spike,surge,transient & noise.

1 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)