What is the maximum operative of Drive ?

Answers were Sorted based on User's Feedback



What is the maximum operative of Drive ?..

Answer / kp

AC Drve operative for following features.
1.it is safty for motor.
2.energy saving.
3.Braking
4.costing/ramping.
5.easy to understant where is fauilure.
6.interlocking according to loop for Speed refrencr.
7.control V/F

Is This Answer Correct ?    5 Yes 0 No

What is the maximum operative of Drive ?..

Answer / stouhidee

At which the drive is use without any damage at its max.
efficiency.

Is This Answer Correct ?    0 Yes 3 No

Post New Answer

More Instrumentation Interview Questions

whatis diference between zero pressure and obsolute pressure

1 Answers   ABB,


We do have a problem in the company that is one PT connected to PlC which is mean 1 out of 1 in PLC system we do have the PAHH is 55 mbar and PALL 8 mbar with a timer of 15 sec for the PAHH the problem started when PAHH goes more than the set point which is 55 it reached up to 71 but due to timer doesn't trip . We force it and we checked everything nothing there . We replaced the transmitter problem still there the reading goes more than the 55 bar the range for transmitte is 0- 60 mbar . So we did loop check , aculaizing valve , wiring all are okay . What the possible causes for this ???

2 Answers   National Petrochemical Company,


how magentic flow tx. vortex flow tx & ultrasonic flow tx works and its prinicle?its callibtration prosedure?

1 Answers  


What is actuator what is motorized control valve?

5 Answers   Emco,


There are two chlorination tonners both are connected to two pressure swithes and the pressure switch is connected to SOV which operates the valve to changeover the tonner selection i.e if pressure one tonner goes low the other tonner should come in line if it is inautomatic selection design a circuit using relays ?

0 Answers  






In control valve proximity inductive sensor is taken as digital feedback for full open and full close.Normally its volts 24v when the sensor acts the feed back voltage 14v so that our relay not indicating in plc panel . kindly give the solution.

0 Answers  


why we use 24v dc in instrument rahter than 230vac????

4 Answers  


What is the SCAN time of a DCS/PLC? What is the typical value for scan time of DCS and PLC?

6 Answers   Essar, Gasco, Siemens,


How to gennerate earth leakage monitoring alarm for solenoid valves in control system?

2 Answers  


What are primary elements of measuring pressure? Which type of pressure can be measured by these elements?

0 Answers  


all types instrumentation questions want

0 Answers   Bhel, Descon, HBL Power Systems,


What is a PID controller and how can it to applied to our everyday life?

4 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)