Answer / khursheed

Metering CTs have saturation restrictions to protect the
measuring instruments, but Protection CTs has higher limits
of saturation.

Answer / k.prabhakar reddy

Metering CT:Wil be used for the purpose of measuring of
current only.
Protection CT: Wil be used for the purpose of protection of
the power devices

Answer / kaarthikrt&c

Metering cts used only in measuring secondary currents(in
view of primary current),no knee point voltage ,winding
resistance is low.
Protection cts r used incase of any faults in d system,knee
point voltage is there,winding resis. is high.

Answer / ullas

metering ct= this belongs to accuracy class .1, 1 etc.
and used to measure current, can be indicated in ammeter
and also can be given to an energy meter to measure kwh.
the cts belong to this class is not used for back up
protection or main protection .
protection cts== this cts can be divided in to backup
protection cts and main protection cts.
backup protection cta belongs to calss 5p10, 10p10, 15p10
etc. these ct are used to give over current and earth fault
protection.
special protection cts= this is used for differetial, ref
protections.class ps
oe main thing you should understand is that these are
coming as different cores of a single ct.
that means a ct with 3 or 4 cores.
each core is meant for different purposes like metering,
backup, special (main) protecton.
i think u ca understand better now.

Answer / vijayakumar

Metering CT:Wil be used for the purpose of measuring of
current only.
Protection CT: Wil be used for the purpose of protection of
the power devices

Answer / lalit barsker

IN METERING C.T. SECONDARY(LOW VOLTAGE SIDE) OF THE CT IS
CONNECTED TO THE METER I.E. AMMETER WATTMETER e.t.c.and in
protection C.T. SECONDARY(LOW VOLTAGE SIDE) OF THAT CT IS
CONNECTED TO RELAY FOR PROTECTION PURPOSE WHEN FAULT OCCURS
RELAY SENSE IT AND C.BREAKER TRIPS.

Answer / krishnan

The class between metering and protection will be diffrent.

Answer / cnsubudhi

metering ct exclussively used to measure electrical
parameters.Where as protection ct used to protect the
devices.

Answer / karthikeyan

Metering CT: Wil be used for the purpose of measuring of V,
A, PF, Frequency etc.

Protection CT: Wil be used for the purpose of protection of
the power devices

Answer / venkatesh

ct measuring the currentand protection ct for
busbar,overcurrent.

why the substation require din electrical system?

1 Answers  

why do we carry out winding resistance test?

0 Answers   MahaGenco, MAHINDRA,

How to find out kvar from any particular load capacity give a formula

3 Answers  

what is meant by phase &line voltage, how its differ from each other ?

5 Answers  

What should be the percentage increase in length of the dead end clamp for bus bar conductor (Hawthorn) after hydraulic pressing and what should be the applied pressure?

0 Answers  

what is numerical relay explain its operation

2 Answers   ABB,

How to do cable earhing? whether by grounding Armour to ground or by running extra G.I wire along with cable? which one is preferred mostly amoung them? If the second one is more preferable how many GI wires to be run along with cable (1 or 2)?

0 Answers   HAL,

what is the difference between rectifier and converter and commudator?

0 Answers  

How can i modify the design of 3 phase induction motor to be as 3 phase synchronous motor??

2 Answers  

I am getting above 60 V as open delta voltage against single phase unit ICT at tertiary delta formed and ICT getting trippped on NDR. ICT tested and found in order. PTs provided on tertiary are tested and in order. what may be the reason?

0 Answers  

what is the earthing condition between earth & neutral.

6 Answers   ABB,

How to find synchronous motor speed formula Ns=120f/P ?....

2 Answers   Cranedge,