difference between ceiling fan

Categories >> Engineering >> Electrical Engineering
Suggest New Category

Question Posted / ayyappss

24 Answers
52945 Views
Altius Technologies, Raisoni, TCS, Uni Deritend, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

difference between ceiling fan..

Answer / ayyappss

In ceiling fan stator is rotating part and in table fan
rotor is the rotating part

Is This Answer Correct ?

140 Yes

50 No

difference between ceiling fan..

Answer / pandi

in celing fan outer portion of the motor is rotated.table
fan inner portion is rotated

Is This Answer Correct ?

79 Yes

18 No

difference between ceiling fan..

Answer / popoulus

Ceiling Fan Rotates Anti Clock Wise
Table Fan Rotates Clock Wise

Is This Answer Correct ?

35 Yes

4 No

difference between ceiling fan..

Answer / pyobik

simply saying;
Ceiling fan bears an external rotor! and internal stator.
whereas table fan or dryres etc have internal rotors and
external stators.

Is This Answer Correct ?

38 Yes

11 No

difference between ceiling fan..

Answer / nareshchandra jha

In celing fan stator rotates whereas in table armature
winding rotates .

Is This Answer Correct ?

13 Yes

4 No

difference between ceiling fan..

Answer / rahul gaurav

Ceiling fan is in the upward direction whereas table fan is
in the lower direction we used

Is This Answer Correct ?

8 Yes

0 No

difference between ceiling fan..

Answer / gopinath

If we see the direction of rotation also differnt in
celling fan and table fan.Because in celling fan sator was
rotated but in table fan rotor wind was rotated.

Is This Answer Correct ?

36 Yes

29 No

difference between ceiling fan..

Answer / n.dinesh

In celing fan stator will rotat.
In table fan rotor will rotat.

Is This Answer Correct ?

19 Yes

15 No

difference between ceiling fan..

Answer / sb

in cel fan single phase capacitor start capacitor run
induction motor is used. But in tablr fan reluctance is used

Is This Answer Correct ?

6 Yes

2 No

difference between ceiling fan..

Answer / s. rajeshkumar d.eee

In Ceiling Fan The rotar is stationary, when the power supply is in on condition the supply in the coil induces the magnetic flux in the rotor these magnetic lines are cut by the stator and it turn to run in anticlockwise direction...

In Table Fan the rotar is the rotating part, When the power supply is in on condition the supply in the coil induces the magnetic flux in the stator these lines are cut by the rotor and rotates in clock clockwise direction

Is This Answer Correct ?

5 Yes

1 No

Post New Answer

More Electrical Engineering Interview Questions

How do we calculate over and under frequency tolerance from generator data?

0 Answers DPS,

When Alarm report at LED,Alarm volatge is 11-13 Volt But LED is of 3 volt.then why not it burn?

0 Answers

What is mean by nominal voltage,Explain?.How much nominal voltage?.

1 Answers

what is lowest system voltage?

7 Answers Apex Holdings,

What are the conditions for sustained oscillator or what is backhouse criterion?

0 Answers

why maintenance batteries used in DG sets not in MAintenance free Batteries.

4 Answers

How to find out damper winding failure for synchronous machine?

0 Answers

how can 3phase motor speed can be controlled without vvf drive?

1 Answers

How you take care of a motor from over loading and what are the different overloading ratings of different motors?

4 Answers

can any one suggest paper presentation topies for electrical engg?

0 Answers

I have 11KV/415V power distribution transformer. I have found unbalance current in LT (415V) side. Also observed that unbalance voltage (3V) at LV side due to HV side unbalance voltage. What should I check for this? Also, the same LV side load can run in balance on captive power.

1 Answers

Define phase cross over?

0 Answers

For more Electrical Engineering Interview Questions Click Here