Answer / bhanu satya prasad

if the secondary of the ct is open ,this condition will
stress ct and dangerously high voltage will be induced in
the secondary ,there may be a chance for sever hazards

Answer / raxit

because of primary,there is flux linkage in secondary.so
current will flow through secondary.but if there is no close
path,current will not flow.but due to electromagnetic
induction high voltage will be built up across the secondary
terminal and the current transformer will BLAST

Answer / @neesh

there should be very high voltage on secondary..it is
dangerous..............

Answer / soewinaung

Never open secondary of C.T. There will be very high voltage
in the secondary winding. C.T will be blast.

Answer / ramu

if secondary of current transformer is kept open it will
blast

Answer / sudhar

if secondary is kept open,the rated current inthe primary
will be induced in the secondary side.due to open ckt,the
curent wil be zero.so high voltage will pass which will
burn the secondary coil and the devices connected to it

Answer / dinesh

If the secondary opened , due to inductive property a very
high transient voltage induced at the secondary side as a
result insulation of secondary side brust and it became
damaged

Answer / hareesh

it is normally a step up transformer,high voltage will
induse in secondery since there is no opposing flux for
primery.it is normally used for measuring purpose no current
will flows through it.flux will saturate.

Answer / ankush miglani 9718037333, eba

there is voltage n so current in primary side.
now due to emi voltage induced in the secondary side.
if the 2dry is open the current becomes zero, which makes
the infinite impedance n results in very high voltages
sometines in kilovolts which may produce arcing.

Answer / deltawye

if the secondary line of a transformer is open the current
is zero,but the voltage is still present and it depend on
the transformer rating on the secondary side..

super position theorem is applicable to

1 Answers  

why we ht line cable size small rather than lt cable.

4 Answers   Aster Teleservices,

how df/dt relay operates & how it works?

1 Answers  

What do you mean by distribution transformers?

0 Answers  

When we use air circuit breaker, it has O/L protection ,time delay SC protection, Instataneous SC protection & ground fault protection. They all have some setting range. But what is the suitable/allowable setting for the above protection which will be safe for the equipment? For example-O/L protection setting have a range of (0.4,0.45,0.5,0.55,0.6,0.65,0.7,0.8,0.9,1.0)xIn Time delay SC protection have a range of (1.25,1.5,2,3,4,6,8,10,12)xIn Time delay setting is 0.02,0.1,0.2,0.3,0.4 Instataneous setting is fixed to 20xIn Gound fault setting is given 100A,300A,600A,900A,1200A This setting are for 2500A ACB. So what will be the basic allowable setting for the above protection? is there any formulae to calculate this<

0 Answers   Lupin,

What is PF? Formula for calculating PF in HT side?

10 Answers   HSL,

how we can measure the dc current instead of clamp meter ?

1 Answers  

What are motor generator sets and explain the different ways the motor generator set can be used ?

0 Answers  

when we megger is not damaged when we are measuring very low resistance? high d.c. voltage is produced in megger so according to i=V/R. current will be high so what is the reason ?

1 Answers  

What Normal(Tangent) towers and Tension(Cut-point) Towers?

1 Answers   ABB, BGR Energy, NTPC, Powermec,

give 5 differences between relay and contactor

1 Answers   Texas,

What are the protection required for Transformer, motor, Line, Generator, capacitor, that all i have to refer which standard?(Like Transformer detail IS 2026)

0 Answers