optical fiber losses.

Answers were Sorted based on User's Feedback



optical fiber losses. ..

Answer / hiralal

optical fiber losses in communication

1.Reflection losses
2.Fiber separation
3.Lateral misalignment
4.Angular misalignment
5.Core and cladding diameter mismatch
6.Numerical aperture (NA) mismatch
7.Refractive index profile difference
8.Poor fiber end preparation

Is This Answer Correct ?    163 Yes 21 No

optical fiber losses. ..

Answer / shruthi d

1.Reflection losses
2.Fiber separation
3.Lateral misalignment
4.Angular misalignment
5.Core and cladding diameter mismatch
6.Numerical aperture (NA) mismatch
7.Refractive index profile difference
8.Poor fiber end preparation
9.PROPAGATION LOSS
10.BENDING LOSS

Is This Answer Correct ?    103 Yes 20 No

optical fiber losses. ..

Answer / manoj

optical fiber losses-

1.Attenuation(1.absorption 2.scattering)
2.Dispersion
3.Microbending
4.Macrobending or Curvature losses
5.Cladding effects

Is This Answer Correct ?    36 Yes 10 No

optical fiber losses. ..

Answer / s.manickavasagam

1.Attenuation.
2.Scattering
3.Bending Losses.
4.Dispersion.
5.Cladding Losses

Is This Answer Correct ?    33 Yes 8 No

optical fiber losses. ..

Answer / bhuvika

attenuation
absorption losses - intrinsic absorption
extrinsic absorption
scattering losses -
linear scattering losses *rayleigh scattering
*mie scattering
non linear scattering losses
*simulated brillouin scattering
*simulated raman scattering
bending losses - macro bending losses
micro bending losses
dispersion - modal or inter modal dispersion
material dispersion
waveguide

Is This Answer Correct ?    31 Yes 6 No

optical fiber losses. ..

Answer / pritpalsingh

Absorption losses(intrinsic & extrinsic)

Scattering losses(linear & non-linear)

Radiation losses

Compelling losses

Bending losses(Macroscopic bends & Microscopic)

Dispersion(intramodal,intermodel,polarized)
material and waveguide

losses due to leaky modes

Is This Answer Correct ?    33 Yes 11 No

optical fiber losses. ..

Answer / dharmendra yadav

losses in optic fiber are as follows
1)Absorption losses
2)Scattering losses
3)Dispersion losses
4)Radiation losses
5)Modal dispersion
6)coupling losses

Is This Answer Correct ?    21 Yes 3 No

optical fiber losses. ..

Answer / rushabh

1-atomic defect
2-bending loss
3-scattering loss
4-signai desperson loss

Is This Answer Correct ?    33 Yes 16 No

optical fiber losses. ..

Answer / abdul fathah mk

Intrinsic and Extrinsic loss
bending Losses
Coupling Loss
Dispersion loss
ray Leigh Scattering

Is This Answer Correct ?    12 Yes 7 No

optical fiber losses. ..

Answer / yatish

1.Reflection losses
2.Fiber separation
3.Lateral misalignment
4.Angular misalignment
5.Core and cladding diameter mismatch
6.Numerical aperture (NA) mismatch
7.Refractive index profile difference
8.Poor fiber end preparation
9.PROPAGATION LOSS
10.BENDING LOSS

Is This Answer Correct ?    1 Yes 2 No

Post New Answer

More Electronics Communications Interview Questions

Why circuit turn off time should be greater than the thyristor turn-off time?

0 Answers  


why we used -48 dc volt for telecom equipments ?

2 Answers  


What is the E1 & OmuSig?

0 Answers   NSN,


In a sales interview if a person ask us how would you be able to sell our products in this recesion. How would i have to respond them.

0 Answers  


What are the questions that are asking at iris aptittude question paper

0 Answers   IRIS,






What is PLC ? What it does ? What are its components ? When & where we use PLC & How ? What are its Pros & Cons over other things ? What are the main faults that occur in it ? What are other devices that are similar to it and how we can compare them all ?

0 Answers   Pricol,


why rxlevel is negative valued ???

3 Answers   Ericsson,


The property of a metal that is determined by the indentation on a metal surface

0 Answers   HAL,


CAN A GSM MOBILE TOWER ESTABLISH WIFI FACILITY?

2 Answers  


What ODU work?

0 Answers  


how to calculet the resolution of 4 to 20 mA current signal

0 Answers  


temperature transmitter range o to 100c over range set value 21.6ma if you give source on the field transmitter showing iop out put also 21.6ma but dcs not showing iop samething if you simulat from hart 21.6ma in dcs showing iop how its possible?

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)