Are there flow velocity restrictions to avoid static charge build up in pipelines?

0 Answers  

---

Question 39 - Acetone and ethanol are separated using a distillation column with a partial condenser and partial reboiler. An equimolar, sub-cooled liquid feed enters at 100 kmol / hr and condenses 1 mole of vapor for every 6 moles of feed. The separation requires a distillate vapor that is 95 mol % acetone and bottoms liquid that is 5 mol % acetone. The reflux is returned from the condenser to the column as a saturated liquid and the operation is run at (L / V) = 1.4 * (L / V) min. Assume constant overflow conditions. (a) Feed operating line is y = [ q / (q - 1) ] x - z / (q - 1) where z = 0.5 for equimolar liquid mixture of 2 components, q = (L’ - L) / F where L’ = L + F + (F / 6) for condensation of 1 mole of vapor / 6 moles of feed. What is y = f(x)? (b) The rectifying operating line is y = (L / V) x + (D / V) (xd) where (L / V) min goes through the points A (0.95, 0.95) and B (0.53, 0.69), V = L + D. What is y = f(x)? Let xd = 0.95. (L / V) min is the slope of the 2 points A and B.

1 Answers  

---

What fluid first to be lined up in a heat exchanger whether hot or liquid?why?

2 Answers   TCL,

---

what is cv value in valves

3 Answers   IFFCO,

---

Explain how can one estimate how the friction factor changes in heat exchanger tubes with a change in temperature?

0 Answers  

---

how much time will take 20000 liter water to cool from 80-30 0C ? Assume all parameters constant

1 Answers  

---

Question 52 - The half-life for first order reaction could be described in the differential equation dC / dt = -kC where k is a constant, C is concentration and t is time. (a) Find the equation of C as a function of t. (b) Find the half life for such reaction or the time required to reduce 50 % of the initial concentration, where k = 0.139 per minute. (c) When the initial concentration Co is 16 mol / cubic metre, how long does the reaction required to achieve the final concentration of 1 mol / cubic metre?

1 Answers  

---

If I do M tech in chemical engineering from iit kgp,iit delhi or iit kanpur...what are the job opportunities,and what salary they offered.plz tell me...i had 156 all india rank..i did not take admission ..but this year i m thinking to take admission...

2 Answers  

---

Question 64 – According to a heuristic of chemical engineering plant design, assume a pressure difference dP = 4 psi for each 10-ft rise in elevation. A pump is needed to pump liquid from a storage tank at a lower elevation to a heating tank at a higher elevation with the elevation difference of 60 ft. (a) Find the pressure loss due to such elevation. (b) If the required minimum inlet pressure to the heating tank is 9 psi, with 1 control valve is installed between pump and heating tank, what is the dP minimum required for the control valve and the entrance to the heating tank when the heuristic mentions that at least 10 psi is required for the control valve? (c) The pressure at the inlet of the pump is 8 psi and the flowrate of the liquid produces pressure head of 50 psi. What is the total pressure produced by the pump? (d) Assume a pipeline dP of 2 psi / 100 ft for liquid flow in a pipe according to heuristic, what is the approximate maximum length of the pipe in ft that can be installed between the pump and the heating tank?

1 Answers  

---

What is a common source of error in determining the percent spent caustic in refinery applications?

0 Answers  

---

Cooling water line sizing ?

0 Answers   Deepak Fertilisers,

---

CHEMICAL ENERGY BALANCE - EXAMPLE 11.5 : According to Margules Equation, P = x(1) p(1) g(1) + x(2) p(2) g(2) for a two-component mixture where P is bubble pressure, x is mole fraction, p is saturation pressure, g is constant given by ln g(1) = x(2) A x(2). Find the value of A as a constant when P = 1.08 bar, p(1) = 0.82 bar, p(2) = 1.93 bar in a 50 : 50 mole fraction mixture. Estimate the pressure required to completely liquefy the 30 : 70 mixture using the same equation, by proving P = 1.39 bar. Take note that ln g(2) = x(1) A x(1), ln g(1) = x(2) A x(2).

1 Answers  

---