In case of welded vessels why is stress relieving in the form of post-weld treatment necessary?

0 Answers  

---

ELECTRICAL TECHNOLOGY - EXAMPLE 16.3 : In the design of a solar power system steps of calculations below are followed : (a) The power output of the inverter of the solar panel is 100 watts. What is the power input, Pin to the inverter when the efficiency of the inverter is 50 %? (b) If the rated power of the inverter is 300 watts, how many inverter is needed for the solar panel? (c) Charge controller of V = 12 volts is used to supply power to the inverter. What is the input current I to the inverter? (d) If the charge controller capacity is 10 A, how many charge controllers are needed? (e) If a biochemical mixer consumes 100 watts, running for 2 hours per day, what is the energy consumption in kilowatt hour per day? (f) What is the input energy needed when the efficiency of the inverter is 50 %? (g) If your area receives 2.88 hours of full sunlight per day, how much energy, in kilowatt hour can be produced per day when one solar panel can produce 20 watts of power? (h) If you know that you have to produce total energy as the answer for (f), how many solar panels are needed? (i) Each V = 12 V battery has 5 ampere hours. If the total energy needed is in answer (f), then how many batteries are needed to run the biochemical mixer if without sunlight for 3 days?

1 Answers  

---

What are some good strategies for curing tube vibration in shell and tube exchangers?

0 Answers  

---

What are the chemicals are required for cooling tower passivation? Please mail me in my Email id:-nsput2000@gmail.com

3 Answers  

---

sir, kindly explain to me that how to calculate volume of torrispherical vessel which is used in pharma company ss reactor bottom dish volume. thank u.

0 Answers  

---

Which one is process and why?( evaporation, vaporization, reactor, fluid flow)

5 Answers  

---

QUANTUM BIOLOGY - EXAMPLE 33.3 : In quantum biology, microtubule is used to store information in a cell. At temperature of T = 300 K, measured current I in a probe is directly proportional to the supplied voltage V, when passing through a microtubule with resistance R. (a) Form an equation of V as a function of I involving k as a constant. (b) If the microtubule has R = 1 ohm at such condition, find the value of V when I = 2 A. Hint : Ohm's law. (c) Find the relationship of k as a function of R.

1 Answers  

---

UNIT OPERATION - EXAMPLE 9.4 : Acetone and ethanol are separated using a distillation column with a partial condenser and partial reboiler. An equimolar, sub-cooled liquid feed enters at 100 kmol / hr and condenses 1 mole of vapor for every 6 moles of feed. The separation requires a distillate vapor that is 95 mol % acetone and bottoms liquid that is 5 mol % acetone. The reflux is returned from the condenser to the column as a saturated liquid and the operation is run at (L / V) = 1.4 * (L / V) min. Assume constant overflow conditions. (a) Feed operating line is y = [ q / (q - 1) ] x - z / (q - 1) where z = 0.5 for equimolar liquid mixture of 2 components, q = (L'- L) / F where L' = L + F + (F / 6) for condensation of 1 mole of vapor / 6 moles of feed. What is y = f(x)? (b) The rectifying operating line is y = (L / V) x + (D / V) (xd) where (L / V) min goes through the points A (0.95, 0.95) and B (0.53, 0.69), V = L + D. What is y = f(x)? Let xd = 0.95. (L / V) min is the slope of the 2 points A and B.

1 Answers  

---

Question 51 - A batch reactor is designed for the system of the irreversible, elementary liquid-phase hydration of butylene oxide that produces butylene glycol. At the reaction temperature T = 323 K, the reaction rate constant is k = 0.00083 L / (mol - min). The initial concentration of butylene oxide is 0.25 mol / L = Ca. The reaction is conducted using water as the solvent, so that water is in large excess. (a) Let the molecular weight of water is 18 g / mol and the mass of 1 kg in 1 L of water, calculate the molar density of water, Cb in the unit of mol / L. (b) Determine the final conversion, X of butylene oxide in the batch reactor after t = 45 min of reaction time. Use the formula X = 1 - 1 / exp [ kt (Cb) ] derived from material balance. (c) Find the equation of t as a function of X.

1 Answers  

---

why when we perform SCC of an alternator we always get a straight line even when 125% rated current is flown?

1 Answers  

---

types and working of compressor

1 Answers   IOCL,

---

what is the PH value for boiler water.

12 Answers  

---