How many pounds (lb) are available in 1 kilogram (kg), 1 metre (m) has how many feet (ft) and 1 meter (m) has how many inches (in)?

1 Answers  

---

FOOD ENGINEERING - QUESTION 23.2 : (a) A dryer reduces the moisture content of 100 kg of a potato product from 80 % to 10 % moisture. Find the mass of the water removed in such drying process. (b) During the drying process, the air is cooled from 80 °C to 71 °C in passing through the dryer. If the latent heat of vaporization corresponding to a saturation temperature of 71 °C is 2331 kJ / kg for water, find the heat energy required to evaporate the water only. (c) Assume potato enters at 24 °C, which is also the ambient air temperature, and leaves at the same temperature as the exit air. The specific heat of potato is 3.43 kJ / (kg °C). Find the minimum heat energy required to raise the temperature of the potatoes. (d) 250 kg of steam at 70 kPa gauge is used to heat 49,800 cubic metre of air to 80 °C, and the air is cooled to 71 °C in passing through the dryer. If the latent heat of steam at 70 kPa gauge is 2283 kJ / kg, find the heat energy in steam. (e) Calculate the efficiency of the dryer based heat input and output, in drying air. Use the formula (Ti - To) / (Ti - Ta) where Ti is the inlet (high) air temperature into the dryer, To is the outlet air temperature from the dryer, and Ta is the ambient air temperature.

1 Answers  

---

can u tel me d question paper of gail?

0 Answers   HPCL,

---

What is gibbs free energy?

0 Answers  

---

hi i am chemical engg. 4 year student i am not placed till year what will i do for my batter futere

3 Answers  

---

What are the three classes of organic solvents?

0 Answers  

---

PLZ ANYONE SEND ME PLACEMENT PAPERS OF I.O.C.L MY ID---- gaurav.nitw.5609@gmailcom

0 Answers   IOCL,

---

What does Dew point -40C mean in an air drying unit.

4 Answers  

---

How can I remove/decrease TDS from sewage waste water? At the moment it is 900gm/l. What is recommended TDS level to dispose sewage water in sea?

2 Answers   OGDCL,

---

CHEMICAL MATERIAL BALANCE - EXAMPLE 2.4 : A mixture consists of benzene (B), toluene (T) and xylene (X). At a temperature of 353 K, the data of vapor pressures : B : 754.12, T : 289.71, X : 91.19. Unit is mm Hg. The pressure P is 0.5 atm. The value of k for each substance is k = (vapor pressure) / P. (a) Calculate k for B, T and X. Let L / V = 0.65. (b) By using the equation V = F / [ (L / V) + 1 ], find the value of V when F = 100, then what is the value of L?

1 Answers  

---

Are there any special considerations to be taken into account for combusting ammonia?

0 Answers  

---

MICROBIOLOGICAL ENGINEERING - QUESTION 28.2 : A hemocytometer is a device that is used for counting cells. In an engineering experiment, 100 microlitres of cell suspension is diluted with 50 microlitres of Trypan blue dye. Only death cells appear blue in color when stained with the dye. There are 57 cells detected in a hemocytometer, where 5.3 % of them appear blue when the chamber of the meter is placed under a microscope. Each square of a chamber can contain 0.0001 mL of liquid. (a) Calculate the number of viable cells. (b) The cells occupied 5 squares. Calculate the average number of viable cells / square. (c) Calculate the dilution factor of the cell suspension by using the formula : Dilution = final volume / initial volume. (d) Calculate the concentration of viable cells / mL by using the formula : Concentration = (Average number of viable cells / square) x dilution x (square / volume).

1 Answers  

---