Answer / raj

You just tell him the size of the nut you want and buy
it,,, for instance u say the ISO sizes such as M3 for a 3mm
dia nut

Answer / rajkumar

For buying a nut we have to specify somewhat like this M8x2
where M stands for metric,8mm stands for diameter and 2
denotes the pitch of the thread.

Answer / yesm

first you give size of nut or bolt as M10,M25 etc
second you mention pitch if want fine pitch then M10X1 or
standard
third you mention class of nut ie applicable load as example
Class 5.8
it means its UTS is 500 Mp and yeild strength is 80% or 0.8
of uts.
that is sufficient

Answer / arul - mz

All have tried to near the answer....

Usually Engineers do have some logic & common sense.

1) Nuts and bolts are used for fastening to a tight a seal
properly without leak or to fasten to prevent unnecessary
vibration. For that we have to tighten based on the torque
that a bolt & nut can withstand.

So selecting the bolt for the required application reuires
the customer to specify CLASS like 4.6, 5.8 etc...

Usually class represeent the material composition of the
nut and bolt.... Greater the value specified will have
higher strength...

2) For buying a nut, any person can offord to buy a nut
also together... this is to prevent the ease of assembly...
No need to mention pitch... Only u have to mention the
class and the size like M12, M16....

Answer / pradeep

Just specify the size of Bolt which you want to buy.
For ex. ask him for M10 size bolt which you want.

Answer / shuhaib mushtaq.

simplly the size of the nut eg,M10, M25
or about the ultimate tensile strength UTS of nut as 3.5,
it means 300Mp UTS & 50% is yield strength

Answer / shaikh arif

by specifing the size of the nut as per the requirement.
for e.g m12 for 12mmdiameter nut & if pitch is also
imortant then specify the pitch with the diameter like
M12mltipyby(pitch.e.g 2mm)

Answer / narendra

basically you give the standard size of nut i.g. M8 which
is gives us the dia. of nut then you told him its pitch
after then the bearing load of nut.

Answer / davender

Just give his part number and quantity so simple

Answer / arun

you give the size of the nut and then the material if it is
SS or MS and if necessary the pitch. In most cases they
dont ask for the pitch as it is a standard

What is latent heat of melting? What is latent heat of vaporization? What is difference b/w steam, wet steam, saturated steam and superheated steam? What is relationship of boiling point and pressure? What is mean by HP steam? What is function of HP steam system? What are main components of HP steam system? What is function of steam strainer? What are conditions for opening of warm up control v/v LBA10AA050? What are conditions for opening of turbine control v/v?

2 Answers  

What is the cold side of the refrigeration system?

2 Answers   RRB,

Who invented springs?

1 Answers  

what is the Tensile strength of M6 Screw

1 Answers  

How do you control cylinder liner wear?

1 Answers   RRB,

• Tell me about yourself:

1 Answers   Petro Star Mount,

functions of gasket

1 Answers  

what is critical temprature

10 Answers   MAHINDRA, TATA,

Hi any one can help in preparing for BHEL ET exam in mechanical stream? I like to know the the question paper pattern fro the same. regards, Jose 9841327666 josevinoth@yahoo.com

1 Answers  

why eta(η) became the symbol of Newton law of viscocity

1 Answers  

Explain how do you calculate cooling energy?

1 Answers  

WHAT IS GEAR TERMINOLOGY?

1 Answers   Focus Energy, Gammon, Honda, Shubham,