Question 49 - According to rules of thumb in chemical process design, consider the use of an expander for reducing the pressure of a gas when more than 20 horsepowers can be recovered. The theoretical adiabatic horsepower (THp) for expanding a gas could be estimated from the equation : THp = Q [ Ti / (8130a) ] [ 1 - (Po / Pi) ^ a ] where 3 ^ 3 is 3 power 3 or 27, Q is volumetric flowrate in standard cubic feet per minute, Ti is inlet temperature in degree Rankine, a = (k - 1) / k where k = Cp / Cv, Po and Pi are reference and systemic pressures respectively. (a) Assume Cp / Cv = 1.4, Po = 14.7 psia, (temperature in degree Rankine) = [ (temperature in degree Celsius) + 273.15 ] (9 / 5), nitrogen gas at Pi = 90 psia and 25 degree Celsius flowing at Q = 230 standard cubic feet per minute is to be vented to the atmosphere. According to rules of thumb, should an expander or a valve be used? (b) Find the outlet temperature To by using the equation To = Ti (Po / Pi) ^ a.



Question 49 - According to rules of thumb in chemical process design, consider the use of an expande..

Answer / kang chuen tat (malaysia - pen

Answer 49 - (a) a = (k - 1) / k = (1.4 - 1) / 1.4 = 0.286. Ti = 25 degree Celsius to degree Rankine = (25 + 273.15) (9 / 5) = 536.67 degree Rankine. THp = Q [ Ti / (8130a) ] [ 1 - (Po / Pi) ^ a ] = 230 [ 536.67 / (8130 x 0.286) ] [ 1 - (14.7 / 90) ^ 0.286 ] = 21.469 horsepowers which is more than 20 horsepowers for expander to be used. (b) To = 536.67 (14.7 / 90) ^ 0.286 = 319.629 degree Rankine. The answer is given by Kang Chuen Tat; PO Box 6263, Dandenong, Victoria VIC 3175, Australia; SMS +61405421706; chuentat@hotmail.com; http://kangchuentat.wordpress.com.

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More Chemical Engineering Interview Questions

At what temperature does water have maximum density?

0 Answers  


Explain the different ways in which solids can be blended?

0 Answers  


Is there a handy way to determine if a horizontal pipe is running full if the flow rate is known?

0 Answers  


Question 69 - A well delivers 225 US-gallons per minute of water to a chemical plant during normal system operation. (a) Calculate its flowrate in the unit of mega US-gallon per day or MGD. (b) The following formula is written next to the chlorine feed point : (chlorine feed rate, lb / day) = (flowrate, MGD) X (dose, mg / L) x (8.34). If this formula is correct, then what should the chlorine feed rate to be in pounds per day (lb / day) if the desired dose is 2 mg / L. (c) Prove by calculations that the constant 8.34 in the formula next to the chlorine feed point is correct. Let 1 US-gallon = 3.78541 L and 1 mg = 0.0000022046 pound.

1 Answers  


CHEMICAL MATERIAL BALANCE - EXAMPLE 2.3 : A 1.5 weight % aqueous salt solution is concentrated to 4 weight % in a single-effect evaporator. The feed rate to the evaporator is F = 7500 kg / h and the feed is at 85 degree Celsius. The evaporator operates at 1 bar. By assuming that only pure solvent of water exists in the form of vapor from the feed, calculate the flow rate of such vapor V.

1 Answers  






Explain how is waste heat boilers categorized?

0 Answers  


How to calculate the release flowrates from pressurized gas systems?

1 Answers   Reliance,


What are some common methods for helium leak testing a vacuum system?

0 Answers  


Question 87 - According to Hardy-Weinberg Equation, p x p + 2 x p x q + q x q = 1 where p = dominant allele frequency and q = recessive allele frequency. Let p + q = 1. Fraction of population has 2 copies of the p gene = p x p. Fraction of population has 2 copies of the q gene = q x q. Fraction of population has a copy of p gene and a copy of q gene = 2 x p x q. In a small town, the allele frequency is q = 0.2 for a recessive gene, the delta-32 mutation, that gives human protection from HIV infection. (a) Find the allele frequency a dominant gene, p. (b) What percent of the population has at least a copy of the gene that cause the population either immune to HIV or less susceptible to the disease?

1 Answers  


from which book shud i will prepare for the hpcl and various company exma i m fresher and my basic is not strong could u suggest from where to start

7 Answers   IOCL,


What are the different ways in which solids can be blended?

0 Answers  


who is the first atomic scientist in india?

5 Answers   IGCAR,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)