where transformer is installed? a)generating station b)substation c)voltage r

Categories >> Engineering >> Electrical Engineering
Suggest New Category

where transformer is installed?
a)generating station
b)substation
c)voltage regulating area

Question Posted / anandswaruppandey5

6 Answers
7132 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

where transformer is installed? a)generating station b)substation c)voltage regulating area..

Answer / sanjay

transformer is used in
1-genrating station(step up)
2-substation(step down)
3-transmission line(booster)
thus transformer is used where voltage is required at
desired level.
for above one answer (c) seems to be d right one.

Is This Answer Correct ?

8 Yes

2 No

where transformer is installed? a)generating station b)substation c)voltage regulating area..

Answer / saurav

b)substation

Is This Answer Correct ?

6 Yes

5 No

where transformer is installed? a)generating station b)substation c)voltage regulating area..

Answer / richard

Power Transformers are installed at

1. Power stations to step up from the generation voltage to
transmission voltage.

2. At Sub Stations for either step down to transmission
distribution voltage or as interconnector link for
transmission lines

Is This Answer Correct ?

1 Yes

1 No

where transformer is installed? a)generating station b)substation c)voltage regulating area..

Answer / biswaindu parida

Just remember Transformers are required where voltage step up or step down is there.
In generating stations we step up generating voltage of 12 Kv to 132 Kv for transmission purposes so we need transformers.
In substaion step down of voltages takes place so we need transformers.so do for voltage regulating areas too.

Is This Answer Correct ?

0 Yes

1 No

where transformer is installed? a)generating station b)substation c)voltage regulating area..

Answer / guest

b) substation

Is This Answer Correct ?

0 Yes

2 No

where transformer is installed? a)generating station b)substation c)voltage regulating area..

Answer / rinkesh bhesaniya

Each place

Is This Answer Correct ?

0 Yes

3 No

Post New Answer

More Electrical Engineering Interview Questions

Why generating power limited to 11kv?

4 Answers PSU,

what s a servo motor? how to control the servo motor? and its application, purpose of using?

2 Answers Arabian Pipes,

What is the difference between type1 and type2 relay protection co-ordination for motor feeders

0 Answers DAE,

Why power factor is arising in electrical circuit, is it possible to eliminate from the circuit, why

2 Answers

why in dc generator field rheostate kept in maximum position?

1 Answers

why secondary terminal of current transformer should not be open circuited?

4 Answers ABB,

what about the power of wattmeter at starting and loding?

0 Answers TATA,

Is it possible to obtain 480v or 550v in single phase output by giving the input to 230v to a single phase torodial type transformer without using a stepup transformer?

0 Answers

WHAT IS THE ANALYSIS OF FREE WHEELING DIODE IN FULL WAVE CONROL RECTIFIER?

1 Answers

how can get electrical "c" licence.i am complited in DEEE.PASSING YEAR OF 1993.WORKING IN PVT COCERN LT LINE.PLEASE ADVISE ME .CELL NO 9994786021

0 Answers

A heater capacity is 3.0 KW on 415V . if supply voltage is 380Volt . what is heater capacity on 380volt . and how calculate and give formulas . Prakash veer singh Roto power Engg.

5 Answers

As the one point of eac phase winding is connected to each other in satr connction. Even if that at distribution side collesion of two diff phases result in to blast. Why?

1 Answers

For more Electrical Engineering Interview Questions Click Here