if dirty fluid is flowing through pipe,how it affects frictional loss?




Answers were Sorted based on User's Feedback



if dirty fluid is flowing through pipe,how it affects frictional loss?..

Answer / sumit

addition of foreign particles (dirt) to a fluid will affect
its density. thus type of flow (laminar or turbulent) may
change as it is depends on reynolds no.
also dirt particles may choke valves or any other thin cross
section that may come in way

Is This Answer Correct ?    3 Yes 0 No

if dirty fluid is flowing through pipe,how it affects frictional loss?..

Answer / muniyandi

ingress fluid density and control valves internal leakage will be ingress and pump and cylinder seal damage system output will be degrees

Is This Answer Correct ?    0 Yes 0 No

if dirty fluid is flowing through pipe,how it affects frictional loss?..

Answer / parth m patel

due to presence of sedmentals in the dirty fluid,it wil
stick on the surface of pipe and allover loss of velocity
and pressure due to obestraction in the pipe.

Is This Answer Correct ?    0 Yes 1 No




if dirty fluid is flowing through pipe,how it affects frictional loss?..

Answer / guest

the dirt may cause an obstrucle to the fuild fuel and can
also close the value through its dust particles.

Is This Answer Correct ?    0 Yes 1 No

Post New Answer



More Mechanical Engineering Interview Questions

"How to check the diode, fuse and bearer switch?"

0 Answers   RRB,


What is the effect of high alkaline water to a boiler?

3 Answers   RRB, Siemens, ABC Inc,


What type of beari ng u will prefer for automobile?

2 Answers   L&T, TVS,


difference between altenator and dyanmo?

3 Answers   Bhel,


time vS speed Graph for mechanical press?

0 Answers  






what are the duties of a production engineer in a power plant?

3 Answers  


While finding the velocity of gear B , in case of a simple epicyclic gear train, why do we take tke velocity of gear A to be ZERO(0)if the arm is rotated with speed equal to that of gear A and in opposite direction?

0 Answers   MNC,


What are the things needed to finish interview successfully from the perspective of interviewee ?

5 Answers   NTPC,


what is the difference between technology and engineering ?

3 Answers  


what's the difference between plummer block bearing and the bushed bearing and where it is used

4 Answers  


how piston moves from bdc to tdc during compression stroke. which force acted to compress the fuel at pressure....

2 Answers  


Hi everyone.. I attended the HAL interview... on 9th dec 2008 @ Bangalore.. the interview was 90% technical... my question are>>>>> 1) Design a rod that should withstand 1000N? (they told that the material is mild steel & they gave me the stress- strain graph for that) 2) what is the principal of hydraulic braking?? 3) whether interchangebility is possible between JIGS & FIXTURES??? 4) what is recent developement in Automobile ENGINE??? 5) abt my final year project (since i m a fresher) 6) some HR questions

3 Answers   HAL, Bhilai Steel Plant,






Categories
  • Civil Engineering Interview Questions Civil Engineering (4646)
  • Mechanical Engineering Interview Questions Mechanical Engineering (3704)
  • Electrical Engineering Interview Questions Electrical Engineering (15793)
  • Electronics Communications Interview Questions Electronics Communications (2638)
  • Chemical Engineering Interview Questions Chemical Engineering (762)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (79)
  • Bio Engineering Interview Questions Bio Engineering (30)
  • Metallurgy Interview Questions Metallurgy (95)
  • Industrial Engineering Interview Questions Industrial Engineering (199)
  • Instrumentation Interview Questions Instrumentation (2884)
  • Automobile Engineering Interview Questions Automobile Engineering (171)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (41)
  • Marine Engineering Interview Questions Marine Engineering (62)
  • Power Plant Engineering Interview Questions Power Plant Engineering (170)
  • Engineering AllOther Interview Questions Engineering AllOther (1336)