Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


what will be the motor terminal box connection arrangement
(star or delta). on what basis it decided?

Answers were Sorted based on User's Feedback



what will be the motor terminal box connection arrangement (star or delta). on what basis it decide..

Answer / milinda4p

it may vary depending on the requirement of the
motor(whether high torque or high speed).but for an example
in a 3 phase induction motor where an high torque is needed
the rotor windings are first connected in star to get rid of
the large current(inrush) at the starting. & then after
starting it is set to delta to have a large current (because
then the voltage across a single winding is square root of 3
times that of in star=> square root 3 times larger current
in single winding) (to have a higher torque)

Is This Answer Correct ?    3 Yes 1 No

what will be the motor terminal box connection arrangement (star or delta). on what basis it decide..

Answer / sasi karthick a

it is standard 6 terminal with 3Starting and 3ending points
of windings. Plz refer the below link for connection
diagram.

for low voltage motors,
Upto 2HP/1.5kW - star
above 2HP/1.5kW - Delta

With the same winding, power of the motor varies 3:1 ratio
in Delta to star.

http://www.elprocus.com/wp-
content/uploads/2013/09/Induction-motor-winding-terminals-
connected-in-star-and-delta-configuration.jpg

Is This Answer Correct ?    1 Yes 0 No

what will be the motor terminal box connection arrangement (star or delta). on what basis it decide..

Answer / raj.s

it depends on motor rating if it star typr connection will
made by shorting one terminal bed fully,
if it delta motor then accoding to diagram terminal
connections will occur in terminal box.

its just a connector ,we can made eithr star or delta.

Is This Answer Correct ?    0 Yes 2 No

Post New Answer

More Electrical Engineering Interview Questions

when is the Ohms law is applicable?

11 Answers   ABB,


what effect will 10 milliampere current cause to human body

1 Answers   NPCIL,


what is SWA type of cable?????

4 Answers  


how the specific fuel consumption of 320 kva deisel genarator set (explain with formulas please)?

2 Answers   RRB,


Any body can help me in getting LT panel test procedure.

0 Answers   TATA,


usually why bettery voltage are 1.5V, even if you open a 9V battery there are six 1.5V batteries in series. is it not possible to increase this voltage other than putting in series

1 Answers  


why colour of electrical equipment( like transformer) is grey

10 Answers   Trident,


In MEP Services what are parts of STP and what are there function?

0 Answers   Tenon,


What are n circles?

0 Answers  


What is K-rated transformer? What is the use of it? What can be the size(pls provide calculation if possible) of K- factor transformer for 550kW,690V motor operating with drive (VFD)?

0 Answers  


Is it possible to connect a safety device in to parallel?

0 Answers   Jones Lang LaSalle,


what is power and what is watts detailed description and formulas

2 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4453)
  • Electrical Engineering Interview Questions Electrical Engineering (16638)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)