Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


Why combustion chamber is used in gas power plant cycle?
What will happen if compressor output is directly provided
to gas turbine?

Answers were Sorted based on User's Feedback



Why combustion chamber is used in gas power plant cycle? What will happen if compressor output is d..

Answer / karthick

In combustion chamber only, hot expanding gases can be
produced.In compressor only the pressure of the air is
increased but the temperature of the air is not increased
sufficiently.but in order to produce power high heat energy
gas should expand inside the turbine so that only heat
energy can be converted into mechanical energy.So it is
necessary to use combustion chamber.

Is This Answer Correct ?    4 Yes 2 No

Why combustion chamber is used in gas power plant cycle? What will happen if compressor output is d..

Answer / seshasai

Then, work utilized by compressor will be higher than work produced by turbine...

Is This Answer Correct ?    0 Yes 0 No

Why combustion chamber is used in gas power plant cycle? What will happen if compressor output is d..

Answer / mechanicalboyishere

combustion chamber is used in gas turbine to increase the kinetic energy of the gas.when gas is passed through the compressor the pressure of the gas is increased but a slight decrease in the k.e.of the gas takes place.

if compressor output is directly provided to gas turbine then less amount of work will be done.

Is This Answer Correct ?    0 Yes 3 No

Post New Answer

More Mechanical Engineering Interview Questions

In a rankine cycle if maximum steam pressure is increased keeping steam temperature and condenser pressure same, what will happen to dryness fraction of steam after expansion ?

0 Answers  


How to calculate 12000 litres water store in tank...so what is the dimensions of tht tank?

3 Answers   ACB, GMR,


what is gear ratio & how it can calculate

9 Answers   MAHINDRA,


The shear modulus of most materials with respect to modulus of elasticity is less than half why?

1 Answers   DRDO, RVNL,


What are orthotropic materials ?

0 Answers  


Enumerate some trouble of fuel injection valve

0 Answers  


IN POWER PLANTS NORMARLY BOILER DRUMLEVEL TRIPPING GIVEN AT 20% OF WATER BUT WHY NOT THEY GIVE AT 0% OF WATER?

2 Answers  


What happened if the exhaust valve is leaking?

2 Answers   RRB,


What do u mean about Gear Coupling Number like 101,102,103.....110,112....and how u will get proper Number of Gear Coupling.,Explain it.

2 Answers   TATA,


Are mechanical seals in pumps direction specified?

4 Answers   Sail,


For which parts the wahl factor and lewis form factor used ?

0 Answers  


I got i20 for university of bridgeport,university of new heaven and eastern michigan university.Please tell me visa success rate for these universities.And I want to go to Connecticut.At that place two universities are avaliable one is new heaven and the another one is bridgeport.Which is the best? Please give reply as early as possible.

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4456)
  • Electrical Engineering Interview Questions Electrical Engineering (16639)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)