can we identify the direction of power flow in transmission line by after only

Categories >> Engineering >> Electrical Engineering
Suggest New Category

can we identify the direction of power flow in transmission
line by after only looking the tower

Question Posted / amir_7442

7 Answers
19959 Views
TNEB Tamil Nadu Electricity Board, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

can we identify the direction of power flow in transmission line by after only looking the tower..

Answer / jitendra pawar

We can not identified what is the direction of power flow
in transmission line by after looking the tower because
tower and line from incomer and outgoing both are similar
it's not idendical.

Is This Answer Correct ?

13 Yes

5 No

can we identify the direction of power flow in transmission line by after only looking the tower..

Answer / manoj kumar singh

Yes: The phase indicating plates installed on the tower are
always facing towards the sending side.

Is This Answer Correct ?

8 Yes

1 No

can we identify the direction of power flow in transmission line by after only looking the tower..

Answer / ashok

not identified because power not visible.

Is This Answer Correct ?

10 Yes

7 No

can we identify the direction of power flow in transmission line by after only looking the tower..

Answer / mustaan

Yes: The phase indicating plates installed on the tower are
always facing towards the sending side.

Is This Answer Correct ?

5 Yes

3 No

can we identify the direction of power flow in transmission line by after only looking the tower..

Answer / ravi kumar

power not visible

Is This Answer Correct ?

1 Yes

2 No

can we identify the direction of power flow in transmission line by after only looking the tower..

Answer / manoj sharma

asin single ckt in the dirn of danger plate
in double ckt this pricpl doesnt follow as pwr
flow in both dirn in double ckt

Is This Answer Correct ?

1 Yes

3 No

can we identify the direction of power flow in transmission line by after only looking the tower..

Answer / gulab chandra

The phase indicating plates installed on tower are always facing towards load side.

Is This Answer Correct ?

1 Yes

5 No

Post New Answer

More Electrical Engineering Interview Questions

how to carry out Magnetizing Current Test on Distribution transformer and what purpose we are doing this test.

1 Answers CPCL,

Can anyone explain, How will get positive to ground and negative to ground reference voltage in dc system

1 Answers NCC,

Can I parallel 1 MVA generator with 1kVA Generator? if V, F, Ph Seq and Ph angles are same

2 Answers

How we can come to know the substation range,without go through any name plate ?

0 Answers CG,

What causal system?

1 Answers NTPC,

What is LMU and LMDU. in PLCC communication of 132 kv transmission line. is it possible to use only one LMU with out LMDU ?

1 Answers

HOW MANY TYPES OF FUSE?

0 Answers

DG B-check,C-Check,D-check is depending upon the running hrs.If the running hrs is not reached as mentioned.How to conduct the DG checks.

15 Answers Blue Star,

I have 1500/1A CT If i connect this CT in 6.6KV bus bar means what will be the voltage present in CT?

0 Answers KCL, MPC,

what is the earth to neutral voltage(maximum and minimum) according to ieee standards

4 Answers

For these 2 devices what their power ratings are ? 1) single phase : AC 220V & starting amps 3Amps (i.e. starting torque) and the stabilized amps 2A ... For deep freezer 2) single phase : AC 220V & starting amps 2.7Amps (i.e. including the starting torque of a CRT monitor) and the stabilized amps 1 Amps thanks

1 Answers

which fault is severe and why?between lll fault and lllg fault which fault is severe and y?

0 Answers GE,

For more Electrical Engineering Interview Questions Click Here