why selected genration, transmission or any at 11kv, 132,
220, 220 or 440 voltage which is propotional to 11. why
does not any for ex. 12 kv 13kv or any

Answers were Sorted based on User's Feedback



why selected genration, transmission or any at 11kv, 132, 220, 220 or 440 voltage which is propoti..

Answer / c.haribalakrishnan

Form factor of an alternating current waveform (signal) is
the ratio of the RMS (Root Mean Square) value to the
Absolute Average Value (also referred to as the Practical
Average Value) of the waveform.In the case of a sinusoidal
wave ie., an analogue wave, the form factor is
approximately 1.11. In the case of a square wave ie., a
digital wave, the RMS and the average values are equal;
therefore, the form factor is 1.

That is why generation,transmission Volatges is
proportional to 11...

Is This Answer Correct ?    6 Yes 0 No

why selected genration, transmission or any at 11kv, 132, 220, 220 or 440 voltage which is propoti..

Answer / sachin lakhe

Electricity (voltage)is in form of 110,220,440. or
11 kv,22kv,33kv

means 10% line losses have been considered thats what
Voltage range is in this way.

Is This Answer Correct ?    0 Yes 5 No

Post New Answer

More Electrical Engineering Interview Questions

How to test the vector groups of 3 winding transformer & phase displacements

2 Answers  


Why the transformer rating is denoted in VA rating why not in KW

7 Answers  


What is the transfer function?

0 Answers  


what will be the effect if you were using different brands of outlets?

0 Answers   TESDA,


(1) From the following option, which option is correct for largest size transformer.? a)1KVA,25Hz , b)1KVA,50HZ , c)1KVA,60Hz , d)1KVA,100Hz

5 Answers   Torrent Power,






definition of fault level in powersystems?

4 Answers  


what the different types of cables used for 11kv and 33kv over head work and what is the size of cable in sqmm.

2 Answers   Ordnance Factories Board,


I COMPLITED MY B.TECH AND 10TH CLASS WITH 70%MARKS BUT 12TH CLASS 55%MARKS..CAN I GET INDIAN RAILWAY RECUREMENT EXAMINATION?

0 Answers   UPSC,


why do we use spark detector inside the slip ring brush compartment 0ona slip ring induction motor?

0 Answers  


srij i need the relationship b/w KW AND KWH and with an electrical example. plz send if u can?

4 Answers  


If a surge divertor is required to be protected by 32 amp C Curve Circuit breaker does this limit the amount of protection from surges that you will acheive

0 Answers  


WAT IS MEANT BY COLD AND HOT START OF A MOTOR?? HOW DOES IT AFFECT A MOTOR'S PERFORMANCE??

4 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)