what is the setting of locked rotor in HT motor ? (answer expecting in percentage)

2291

why we use kg/cm2 instead of kg/m2 as a unit of pressure. As we know kg is a MKS unit and cm is a CGS unit. So why we use combination of both(kg/cm2)while describing the pressure.

11035

How many cum of 9.5mm stone in 1 ton ?

2536

why electron produce magnetic field when it is in motion?

2153

How to calculate the value of earth capacitance in a transmission line.

2365

What is difference between unity power factor wattmeter and upper power factor wattmeter? In short circuit test of transformer the wattmeter used is unity power factor type or upper power factor type wattmeter?

2763

how synchronous condenser is used in place of synchronous generator with out negotiating IEEE standards? Can i use 3 generators as synchronous generators and 2 generators as a synchronous condensers in an IEEE 14 bus system with out disturbing the standards?

2130

why we are useing plastic under the lean concrete?and whts the advantage?

2738

what are the different sizes of U.G. cable & where these cabl;es are used according to voltage ..

2108

describe the various addressing modes of 8085 processor, also provide an example of each.

1854

My system suddenly get off,when i try to power on then it does not work but when i open it and clean RAM and insert it again, it power on.but after some day same problem? please give the answer (i have also changed RAM it's new.)

1914

Sir, My doubt on cable sizing calculation, Load:74 KW calculated cable 1 run 50mm2. Now client asking us to reduce cable size by increasing runs. Sir, My question now when my mind strikes with 2 options 1) Divide load 74/2 = 36 and calculate cable for 36+36 making it 2 runs or 2) Simply i can divide 50mm2 /2 ie. 2 runs of 25mm2 Please suggest me sir

1939

Calculate the maximum pressure drop that can be allowed to occur across a control valve, so that we can prevent cavitation / flashing from occurring. Use the following formula: Δ P allow = Km (P1 – PvapourA) where, Δ P allow - the maximum allowable differential pressure for sizing purposes, or terminal pressure drop; Km- the valve recovery coefficient from the manufacturer’s catalogue; P1 - absolute inlet fluid pressure; PvapourA - absolute fluid vapour pressure at the inlet temperature; Use Atmospheric pressure = 101.3 kPa, P1 = 1200 kPa(g), PvapourA = 4 kPa, KM = 0.72

2218

What does afbc stand for?

1166

What is meant by D-FF? What is the basic difference between Latches and Flip flops? What is a multiplexer? How can you convert an SR Flip-flop to a JK Flip-flop? How can you convert an JK Flip-flop to a D Flip-flop? What is Race-around problem? How can you rectify it? Which semiconductor device is used as a voltage regulator and why? What do you mean by an ideal voltage source? What do you mean by zener breakdown and avalanche breakdown? What are the different types of filters? What is the need of filtering ideal response of filters and actual response of filters? What is sampling theorem? What is impulse response? Explain the advantages and disadvantages of FIR filters compared to IIR counterparts. What is CMRR? Explain briefly. What do you mean by half-duplex and full-duplex communication? Explain briefly. Which range of signals are used for terrestrial transmission? What is the need for modulation? Which type of modulation is used in TV transmission? Why we use vestigial side band (VSB-C3F) transmission for picture? When transmitting digital signals is it necessary to transmit some harmonics in addition to fundamental frequency? For asynchronous transmission, is it necessary to supply some synchronizing pulses additionally or to supply or to supply start and stop bit? BPFSK is more efficient than BFSK in presence of noise. Why? What is meant by pre-emphasis and de-emphasis? What do you mean by 3 dB cutoff frequency? Why is it 3 dB, not 1 dB?

2081