I have raw material for making Compact-Choke for flourscent
lamp of 40 Watts. We are suppose to get 0.4 amps output at
end. but we are getting 0.42 or 0.44 amps and above. We
have done many testings in different but nothing worked out.
Please suggest me how to get the correct output.
We are using 1. core winding of 700 windings of aluminium
2. E-shape iron fillings and I-shape iron fillings to
surround the winding.
Answers were Sorted based on User's Feedback
Answer / faisal
SEE ONE THING I TELL U IS THAT TO GET THE CORRECT O/P
CURRENT WHATEVER MAY BE IT IS MAINLY DEPENDS ON THE QUALITY
OH WIRE USED TO WINDING AND THE LARGE LOSSES DUE TO
MATTERIAL USED FO E SHAPE IS MORE LOSSABLE.U TRY WITH 32SWG
WIRE HAVING 750 TURNS U GETT IT EXACT .5AMPS
Is This Answer Correct ? | 6 Yes | 1 No |
Answer / samaruh
Hi Faisal..
Could you contact me on samaruh@gmail.com..
I need to ask you some questions.
Thanks
Samaruh
Is This Answer Correct ? | 2 Yes | 0 No |
Answer / sunil
Chadra,
just hit smoothly on choke, then test it, most probably u
will get o.4amps, if u dont get required value then
increase the no.of wounds up to 718, and make voltage 230
(Fix the voltage on 230V.)then try it again I hope u will
get. All the best.
Could you please inform me that where are you getting the
raw material?
Is This Answer Correct ? | 1 Yes | 0 No |
Answer / ramprakash.b.s
SEE ONE THING I TELL U IS THAT TO GET THE CORRECT O/P
CURRENT WHATEVER MAY BE IT IS MAINLY DEPENDS ON THE QUALITY
OF WIRE USED TO WINDING AND THE LARGE LOSSES DUE TO
MATTERIAL USED FO E SHAPE IS MORE LOSSABLE.U TRY WITH 32SWG
WIRE HAVING 750 TURNS U GETT IT EXACT .5AMPS
i go with this.
Is This Answer Correct ? | 1 Yes | 2 No |
a.)Ammeter and Voltmeter read rms value or avg. value ? b.)What are symmetrical and Unsymmetrical faults?
how to design the heater in temperature control unit to heat 50KL of water?
What is meant by the KA-rating of a circuit breaker? In this regard, discuss the stresses experienced by the circuit breakers
in alternator how we can give power to rotor ? its power is AC or DC ?
why energy storing capacity of magnetic field is much higher than electric field ?
As we use capacitor bank in 3ph ckt to improve PF, can we use capacitor in single ph domestric use, in house we have Fan,Mixer,electric cooker,iron,tube choke they also lag the system,because it is inductive load. if it is possible to improve PF of single ph system-- if yes- type of capacitor to be used,connection diagram, working in detail. if no-- list it.
iii) A shunt motor runs at 70 rad/sec from a 460V supply and takes in an armature current of 100A. Resistors of 2.52 ohms and 1.64 ohms are connected in series with the armature and in parallel with the armature respectively. The field excitation remains direct from the 460V supply but the generated torque is halved. Determine the new running speed. Neglect brush voltage drop. The armature resistance is 0.4 ohms. [15]
What is polar plot?
what is servo motor and how to work it.
I need the recommended size for a 3 phase transformer at 13.8 KV Primary and connected loads of 3000 kVA at 4200 volts and 2375 kVA @ 480 volts AC.
what is meant by LT & HT?
Can u tell me design of switch yard