Answer / student

all the IITs(through GATE), BITS-Pilani(there is a
differents admission procedure other than GATE), chk out the
list of NITs which offer chem engg MTech.

Answer / mradula khandelwal

MNIT,jaipur

Answer / akasharamanna

No college in india facilitate to complete M.Tech. You have
to pass by your self. If you think you can pass, I will
give you certificate in A4 size executive bond paper with
lamination

Answer / jayesh

UDCT Jalgao

What is the import procurement cycle?

0 Answers  

---

Question 54 - There are 2 alternatives of investment. Choice 1 : A trader offers you an investment opportunity where your investment of A$15000 presently will be A$18000 after 4 years. Choice 2 : A bank offers you 5 % annual return for your initial investment of A$15000. Question a : What is the equivalent bank payment after 4 years? Question b : By using the concept of equivalence in engineering economy, which is the better choice, betwen 1 and 2, that will be more profitable after 4 years?

1 Answers  

---

FOOD ENGINEERING - QUESTION 23.2 : (a) A dryer reduces the moisture content of 100 kg of a potato product from 80 % to 10 % moisture. Find the mass of the water removed in such drying process. (b) During the drying process, the air is cooled from 80 °C to 71 °C in passing through the dryer. If the latent heat of vaporization corresponding to a saturation temperature of 71 °C is 2331 kJ / kg for water, find the heat energy required to evaporate the water only. (c) Assume potato enters at 24 °C, which is also the ambient air temperature, and leaves at the same temperature as the exit air. The specific heat of potato is 3.43 kJ / (kg °C). Find the minimum heat energy required to raise the temperature of the potatoes. (d) 250 kg of steam at 70 kPa gauge is used to heat 49,800 cubic metre of air to 80 °C, and the air is cooled to 71 °C in passing through the dryer. If the latent heat of steam at 70 kPa gauge is 2283 kJ / kg, find the heat energy in steam. (e) Calculate the efficiency of the dryer based heat input and output, in drying air. Use the formula (Ti - To) / (Ti - Ta) where Ti is the inlet (high) air temperature into the dryer, To is the outlet air temperature from the dryer, and Ta is the ambient air temperature.

1 Answers  

---

Explain the use of gear pumps in motor?

0 Answers  

---

how to design a heat exchanger?

3 Answers   TATA,

---

---

plz send the interview questions in the written test asked by hindustan petroleum corporation ltd.Iam a b>tech in chemical engineering.My written test is on feb 2008.urgent plz.send the questions to avazithraja@rediffmail.com

9 Answers   AZTEC, Bapex, HPCL,

---

Question 34 – In the distillation of binary systems by Mc Cabe Thiele method, the equation for the line of top section is given by y = [ R / (R + 1) ] x + XD / (R + 1). 2 points on the line are (0.99, 0.99) and (0, 0.36). Find the reflux ratio of R and XD.

1 Answers  

---

MY generator water cooler inlet line height - 11 mtr inlet water line height - 7 mtr water come into the line from overhead tank, O/H tank height - 20 mtr the first tapping in the inlet line is 2" line which down to 4 mtr level plateform., second tapping in inlet water line goes to a pump 6" line installed at 4 mtr level plateform, pump capacity 200m3/hr, head- 30 mtr, hp-40. the outlet of pump of 6" water line connected to a header of 6 mtr long of 6" line, on this header the six tapping are connected, 4 nos. 3" line goes to 11 mtr height water cooler the pressure of the line is 0.15 to 0.25 kg/cm2, 2" and 4" pipe line connected to a cooler at 4 mtrlevel plateform. my question is, at 11 mtr height level the quantity of water and flow is not sufficient for my cooler, the temp. of cooler is rises much more. you are requested to suggest the modification of pipe line/ pump for take more water flow and pressure (desired pressure is 1 kg/cm2)

0 Answers   Simbhaoli Sugars,

---

What is carbon sequestration?

0 Answers  

---

Heat transfer: In a triple effect evaporator, the heat transfer for an evaporator is calculated as q = UA (TI - TF) where TI is the initial temperature, TF is the final temperature; U and A are constants. Given that heat transfer for the first evaporator : q(1) = UA (TI - TB); second evaporator : q(2) = UA (TB - TC); third evaporator : q(3) = UA (TC - TF) where q(x) is the heat transfer function, TB is the temperature of second inlet and TC is the temperature of third inlet, prove that the overall heat transfer Q = q(1) q(2) q(3) = UA (TI - TF).

1 Answers  

---

What are the applications of screen analysis in the chemical industry?

0 Answers  

---

What do we use carburizing/nitriding chemicals for?

0 Answers   Ashok Leyland,

---