Answer / sanjib pramanick

Motor is running as a single phase motor with lower speed
and creating noise. In this situation it will drawing higher
current. If it runs for long time then insulation may get
damage and ultimately burnout the winding.

Answer / rishav

when three 3 phase motor is suddenly single phased .
it will giving sound and its speed lower down. it
may also burn . and mcb or proction will come in
action. because current will rise very high in this
condition

Answer / rajesh shah

If a three phase induction motor is suddenly single-phased
while running, no distinct change will happen if it is
running under noload condition. You will just hear a
hunting sound and the the motor will continue to run with a
slightly lowered speed and increased current, but if the
motor is running under loaded condition it will stop down
and take excessive current due to single phasing and the
protection circuit will trip, if protection ckt is not
installed the motor will be ultimately burnt due to
excessive locked rotor current.
And note: This experiment is tested.

Answer / arvind

if 3 phase motor is suddenly single phased while running
then two phase will supply current to the motor, but it
will draw more current from the main supply,and the winding
will burn out

Answer / syed

Three phase motor suddenly runing single or two phase.Motor
will get over heat and giving noise.this case if we have
protection like breacker it will trip other wise motor will
burn out

Answer / derek

For a Delta connected motor two of the phases (coil sets)
will see normal curent and the other phase will see 200%
current. The supply current in the two remaining phases
will be 173% of normal current. In this situation one coil
is across AC power and the other two coils in series with
each other are in parallel connection with the first.

For a Star connected motor tow coils will carry %173 of
normal current while the other leg has no power. The two
active supply lines will have %173 of normal current.

If the motor is running at %70 load the current may not be
high enough to trip the overload protection and the motor
will overheat.

Slow blow overload protection should be sized to trip in
these conditions.

Answer / rahul

If protection is proper then it will operate and stops the
motor. If there is no protection which is the normal case
in LT motors, then winding will burn there are two diffrent
pattern which will apear depending on the type of winding
connection i.e. delta or star.

You will find most of the winding failure in LT motors
happens due to single phasing.

Answer / stefan

#4
Usually when talking about "single-phased" motor, it means
that two of three phases are connected. In these cases, the
motor will slow down, and the phase currents for the
remaining phases will be increased. I don't know how much. I
am also not sure if the overload device would cut-off the
motor from power supply. Unless problem is not noticed, the
motor will most likely burn. When the motor is opened, you
should be able to see that 2 of the 3 phase windings are
black, and one is good looking (if motor is Y-connected)

Answer / madhusudhana

A three phase motor will continue running if a phase is
lost. Most three phase overload relays are not intended to
provide true single phase protection, so the most likely
scenario is the motor will run at reduced speed for some
time and will eventually overheat and fail. A three phase
motor will not start, on its own, with only single phase.
However, if the motor shaft is "manually" spun it may begin
to turn and accelerate slightly. If the motor shaft is
turned backwards then the motor would start in reverse.

Answer / rajesh sharma

1.if motor conected in STAR than motor two winding burn
2. if motor in DELTA motor one winding burn
3. time duration is depend on load for burning
4. in star R phase is blown than y/b winding burn because
that winding get 440volt and take to much current
5. delta if r phase blown than y pahse winding burn because
only that winding get 440 supply other no.

Is phenomenon of resonance is harmfull fr the machine? if not or if yes please explain it?

0 Answers   Bhel,

how to calculate the input current in singel phase and 3phase supply to 5kva ups

1 Answers   Gravity India,

what is RNG in the DG synchronizing by PLC?

0 Answers  

Are Refrigerators & Deep Freezers the Inductive load ? How to calculate the Power Factor & hence the Output Power for them ?

0 Answers  

sourse is 66 KV / 350 MVA, transfarmer is 1000 KVA 6.6 / 0.415 kv, iF fault is 28.75 MVA on 0.415 KV Bus then calculat the Transfarmer Impidance

0 Answers  

A resistance of 50 kΩ has a conductance of:(a) 20S(b) 0.02S(c) 0.02 mS(d) 20 kS

1 Answers  

What is difference between ball screw and lead screw.

2 Answers  

WHAT ARE THE FACTORS REQUIRED FOR SELECTION OF TRANSFORMER RATING?

13 Answers   Tech Mahindra, Technip,

why we use 50hz frequency in india why not other frequencies like 52,59,42 etc

5 Answers   INTC,

How to decide the fuse ratings for potential transformer

2 Answers   Eskom,

which generator is called as brushless excitation generator and why??

3 Answers  

In an ideal transformer no load primary current I0 A lags behind V1 by 90 degree B is in the phase with V1 C leads V1 by 90 degree D lags V1 by 45 degree

1 Answers