How we check vector group for a Dyn1 transformer?

Categories >> Engineering >> Electrical Engineering
Suggest New Category

Question Posted / amal

6 Answers
27784 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

How we check vector group for a Dyn1 transformer?..

Answer / s.ravindra

The condition of dyn1 was
(a) 1W2N+1U2N=1U1W
(b) 1W2W=1W2V
(c) 1V2W >1V2V

Is This Answer Correct ?

14 Yes

1 No

How we check vector group for a Dyn1 transformer?..

Answer / gunasekaran

we can find out from ratio kit
if applied UV-vn get energised
if applied VW-wn get energised
if applied WU-un get energised

Is This Answer Correct ?

11 Yes

2 No

How we check vector group for a Dyn1 transformer?..

Answer / vinod maurya

We will short 1U & 2U
And we will apply 3 phase voltage between 1U,1V,1W

Measure between
1U-1V
1V-1W
1W-1U
1V-2v
1V-2w
1W-2w
1W-2v
1W-2n
2n-1U

Verify The Condition
1W-2n+2n-1U= 1U-1W
1W-2w=1W-2v
1V-2v<1V-2w

vector group Dyn1 confirmed if the above conditions are
satisfied.

Is This Answer Correct ?

8 Yes

1 No

How we check vector group for a Dyn1 transformer?..

Answer / y.rama krishna

Connect 1U&2U
Apply 3ph 415V balanced voltage across terminals 1U,1V,1W
(HV wdg)
Measure the voltages between the given terminals & record
1)1U-1V
2)1V-1W
3)1W-1V
4)1V-2V
5)1V-2W
6)1W-2V
7)1W-2W
8)1U-2N
9)1V-2N
Verify the conditions
a)1W-2W = 1W-2V
b)1V-2W = 1V-2V
c)1U-1V = (1U-2N)+(1V-2N)
vector group Dyn1 confirmed if the above conditions are
satisfied.

Is This Answer Correct ?

18 Yes

16 No

How we check vector group for a Dyn1 transformer?..

Answer / mahmoud moustafa

The condition of dyn1 was
(a) 1W2N+1U2N=1U1W
(b) 1W2W=1W2V
(c) 1V2W >1V2V
this is correct I check today in one of GE sites

Is This Answer Correct ?

2 Yes

0 No

How we check vector group for a Dyn1 transformer?..

Answer / sakthiyam

i want DdOyn11 conditions

Is This Answer Correct ?

0 Yes

0 No

Post New Answer

More Electrical Engineering Interview Questions

what are the pecularity of shaver sockets ?

0 Answers

Describe the test procedure to determine the vector group

0 Answers MPSEB,

how can we change the phase angle b/w two phase?

2 Answers

WHY MOSTLY Rph IS USED FOR CONTROL CIRCUITS AUX. SUPPLY ?

0 Answers UltraTech,

Can we test the alignment of End shield and stator of turbogenerator without rotor insertion? Also how to fix maintain the alignment at site installation?

0 Answers Deccan Cements,

why we use copper earthing for neutral while for body GI.

1 Answers Chennai Metro Rail Limited CMRL, Valeo Lighting Systems India Private Limited,

What is derating?, Why it is necessary, it is same for all means for drives, motors,and cables.

1 Answers

For polarity test on a 11/3.3kV 2.5MVA delta-star Unit Auxiliary transformer,415V 3-phase supply was applied at the HV. Connection between Aa was made with a 2.5mm cable. As soon as power was switched on the cable caught fire and burnt. This test was then abandoned. It is noteworthy to say that a similar cable was also used in a similar transformer for the same. The cable did not burn and test was successfully completed with good result. What is wrong? Please, help me out.

3 Answers

what is relation between ct and pt ratio with multiplication factor of a energy meter? is there any other factor on which multification factor depend?

0 Answers

why tan delta test conducted in electrical equipmenr

4 Answers

why dc is used in control circuits for MV & LV switchgeras instead of ac

0 Answers

Safety measures in air circuit breaker

5 Answers Megatron Solutions, TCS,

For more Electrical Engineering Interview Questions Click Here