HOW TO CHECK THERMOCOUPLE AND RTD & WHAT IS THE DIFFERENCE
BETWEEN THERMOCOUPLE AND RTD
Answers were Sorted based on User's Feedback
Answer / hafiz muhammad traiq nizami
the output of thermocouple is mV so check the mV in diff
temperatures and the output of RTD is resistance so measure
the resistance at normal temp it should be greater or equal
to that ohm specific of RTD type .For Example if it is PT100
so it will shows minimum 100 ohm if RTD is in working condition.
Diff bet T/C and RTD
both are used to measure temperature but RTD is more
accurate than T/C
RTD can be used upto 800 deg but T/C can be used upto 1750 deg
Is This Answer Correct ? | 2 Yes | 0 No |
Answer / shamim akhtar ansari (jamshed
RTD Works on the Base of Wheat Stone Bridge which is Mention Below
Wheat Stone Bridge:-when RTD heated up Then Create Some Voltage on the Point of Joint Where Galvanometer is Connected.
and voltage should be Equal those Point When the Voltage is Increases then Resistance Will Increase.
that transducer convert these produced Resistance into 4 to 20 MA.
Thermocouple:-it works on the Principal of See Back Effect which is mention below
the Seebeck Effect Describe a Thermo Electric Phenomena by which temperature Difference between two Dissimilar metal in a Circuit convert into electric current.
Is This Answer Correct ? | 0 Yes | 1 No |
Answer / sushma
RTD will be find by R2=R1(1+alpha(t2-t1)) Thermo is used to
measure both AC&DC. In Teromcouple characteristics between
Rstistance & tepmerature is non-linear where as in RTD it
is linear.
Is This Answer Correct ? | 25 Yes | 46 No |
Answer / karthik
put multimeter in resistance mode and check for resistance
b/w wires of rtd or thermocouple,If it shows 0 ohm in
normal earth atmospheric temperature it's fine.And There is
no big difference B/w RTD AND THERMOCOUPLE Accorting to the
measurement range(low temp to high temp),Accuracy it is
Differenciated.
Is This Answer Correct ? | 4 Yes | 29 No |
Galvanizing.
Ple give me "INDUSTRIAL INSTRUMENTATION AND CONTROL S.k. Singh 3th edition" Solution manual to self-Check Quiz and chapter-wise PowerPoint Slides. Home web-site not available... Ple Ple Ple Ple Ple Ple Ple Ple Ple Ple Ple Ple Ple Ple Ple Thanks for all...
Why is the length of cable layyed from RTD to temp. Transmitter should be minimum? Why does heating effect takes place in their?
1 Answers Process Control Technologies,
if i change range of flow transmitter in th field then does it need to change range in dcs?
May I have a brief note above the voltage barriers? Whats is the purpose? Please mail me if you've operational details, mail id: rajkumar.diice@gmail.com
7. What are tri-state devices and why they are essential in a bus oriented system
Instrumentation engineer please reply me,I am electrical engineer ,what is the future in instrumentation dept {presently working (P&ID) Design} for me,whether good future for me as instrumentation department.what side can i get job in future
In most process, speed of motor controlled by control system with a reference pot . Now if i start & it becomes uncontrollable, i.e.gets directly start & stop after certain time.Then which reasons can make such problem? can motor may be faulty?how?
what is axial shift n what is differential expansion in turbine? how many sensor probes r mounted for this n how it works?
How EMF is generated in Thermocouple
What are different types of control valves?
i have steam drum height 1000mm. and i want to placed the transmitter below the tap.how i calculate.