Answer / gajanan

flow of electrical charges or free electrons in close loop
circuit is current

Answer / anbuselvan

Flow of Electron in a closed circuit is called Current.The
Unit of Current is Ampere (A).The Flow of current will take
place if there should some potential Difference.

Answer / kumar

flow of electrons in a conducting material

Answer / yuvi

flow of any material can be called current. Generally it is
associated with fluids. Electric current can be defined as
the rate of flow of charges. Its not mandatory that it
should be electrons (Considering current flowing through
and electolite)

Answer / rajesh_st21

The Rate of flow electron in conducting material is called current.

Answer / pranav upadhyay

Current is a flow of electron which flows from higher potential to lower potential.

Answer / mahantesh

Flow of electron in any closed cricuit that is called
current

Answer / felixraj

coulombs/sec

Answer / azam

rate of flow of charge(electrons)through conducting material
when it is applied by p.d (potential difference) units are
amps (A) BIGGER units KA

Answer / prosenjit majumder

An amount of flow of electron in a closed electrical path
is called current . It depends on the rate of flow of
electrons .

what is the power rating of CPU, CRT type moniter, LCD type moniter,scanner Approx.

0 Answers   HAL,

Draw a 230kv two-bus bar system showing the following. 1.Two generators (150MW) each connected through one 15.75/230KV transformers 2. 1 outgoing lines 3. Two 230/130 KV transformers 4. BUS PT's 5. CT

0 Answers  

Sir,In our company there are 3 caterpillar make(capacity:(1) 3.3KV,2.5MW(2)3.3KV,2.5MW & (3)3.3KV,1.9MW) & 1 deutz make (capacity:11KV,3.8MW)gas engines utilised,all are running in paralell. There are three transformer utilised,(1) 6.25MVA,3.3KV/22KV,Impedence voltage:6.7% used for two generator,both are 2.5MW(2)5.5MVA,3.3KV/22KV,Impedence voltage:7.2% used for one generator of 2.5MW & (3) 5.5MVA,11KV/22KV,Impedence voltage:7.8% used for one generator of 2.5MW.all generator breakers capacity of 1250Amps. Sir,I want the details of fault level calculation of generator,transformer individually & for whole system. If you require any information from me.feel free for contact me sir.pl.send the answer of my question as the earliest as possible.

0 Answers   Piramal Healthcare,

Write the difference between OCB,VCB ?

3 Answers   Svam Power,

how to copy from plc ge fanuc versamax series,all input and output, adress, and printout.

0 Answers   ASM,

What are the effects to a distribution transformer rated 10Kv with ratio 10Kv/0.433Kv, 3phase 50hz for example but fed with power supply of 11Kv?

2 Answers  

Some times to change of DOR of a motor, interchange of R & B is not effected and RYB take same current, but interchange of R&Y is effected ie change the DOR. My doubt is what is the problem in motor and how it is happen.

0 Answers  

What is mechanical interlock?Explain the uses?

2 Answers   HSL,

how we calculate the 30 KW 3phase electric motor current on noload

23 Answers   Monnet, Siemens, SSR, Supermac Industries,

ALONG WITH MEGGER TEST FOR CHECKING OF MOTOR ,WHY WE MEASURE FOR RESISTANCE AND INDUCTANCE?

4 Answers   L&T,

why delta delta connection generally not use in transformer

4 Answers   Lanco,

why we can use 1 to 5V dc

0 Answers