Answer / srinivasansureshkumar

Fire: Fire is a phenoena of chemical process which occurs
when a fuel(source) gets ignited by heat(Motivator) and
cotinues in presence oxygen(sustainer).

** when a fire occurs the resultant products are smoke,
heat and light.

Smoke detectors: Smoke detectors detects the presence of
smoke and initiates an change in circuit to trigger an
alarm/smoke presence.
There are basically two main types of smoke detector used
for smoke detection they are (a) Ionisation type and (b)
Optic type(poto electric).

Fire Detectors: Detects the presence of Light, They come in
varieties in sensing elements such as LDR, Poto diode, etc..
When comes to the area of hydrocarbon fires, these fuels
have an tendency to emit ultraviolet(UV) and Infrared (IR)
light frequency wave lengths. so where UV, ir, UV/ir
detectors are used.

In Breif: Fire Detector detects the light and Smoke
detectors detcts the presence of smoke.

Answer / waibhav

fire detector senses the infrared rays where as smoke
detector senses aerosol .

Answer / nitin diwan

Fire detector only sence the heat accured because of fire
in other side the smoke detector only sence the smoke
accured because of fire...

Answer / ilyas

Fire detector is a common name for all type of detectors to
find fire. Smoke detector is one type of fire detector.If
you have a smoke detector in a pantry it will give always
alarm. so there you have to fix heat detector.If you are
using a smoke or heat detector in a substation you will get
an alarm too late. So A uv detector will be better or you
can use one uv and one smoke detector. Basically all are
intended to indicate a chance of fire.

Answer / elsayem

fire detectors occurs out of building but smoke detectors
inside building

Wht is Dry Leg Calibration and Wet Leg Calibration?

2 Answers  

---

open tank and close tank leavel transmiter about range and calibration

0 Answers  

---

A pressure transmitter with a range of 0-100 bar.The accuracy of the instrument is 1% of upper range value? The pressure indicating transmitter is showing the system pressure is 50 bar. b. When you include the error, what is the minimum possible pressure in our fuel gas system? i. 49.5 bar ii. 49 bar iii. 1 bar iv. 0.5 bar We want to change the filter cartridge. We must depressure the fuel gas system. c. After we depressure the system in preparation for maintenance, the transmitter displays a pressure of +0.1 bar. At this time, what is the possible range of pressures in our fuel system? i. +0.099 to +0.101 bar ii. 0 to +0.2 bar iii. -0.1 to +0.3 bar iv. -0.9 to +1.1 bar

3 Answers  

---

How to measure Flow of air line,what is the procedure of creating DP in line to measure Flow!

3 Answers  

---

Please can anybody tell me the step by step procedure for calibrating the Pr,Lvl,Fl,Temp transmitter on process?

1 Answers  

---

---

can u please give the exact ckt explaination of AC Drive related to industries.

6 Answers  

---

What is the PLC configuration in Cement industry?

0 Answers   IMCO, Maha Cement,

---

i am working in thermal power plant . if temperature transmitter is not showing reading in dcs then how can we rectify the problem?

8 Answers   TATA,

---

What does a hookup diagram look like? can you give sample drawing. thanks.

1 Answers  

---

How we can check the 2 wire proxy switch? & how it is connected to DI MODULE OF PLC?

0 Answers  

---

which instrument is most commonly used to observe the external features of a grasshopper's abdomen?

1 Answers  

---

why is honed type flow orifice plate? what purpose it used? how to select this?

4 Answers  

---