Answer / meher deep

p/vi

Answer / hardworker

Powerfactor is defined as the cosine of the angle between
voltage & current.pf=kW/kVA.It is the ratio of power
utilized to the power delivered.pf depends on the type of
load.
If the load is inductive,pf is lagging.
If the load is capacitive,pf is leading.
If the load is resistive,pf is unity.
pf can be found out from the power triangle.

Answer / ramarpandi

cosine angle between voltage& cureent

Answer / avinash gupta

cosine of angle between voltage and current...so cos fi..

it is a ratio of resistance to impedence..cos fi=r/z

its a ratio between active power/apprent power...=vicosfi/vi
=cosfi

Answer / manasa

Power factor is the ratio between active (real) power to
the apparent power i.e
PF = P/(√P2+Q2)

The power factor can also be calculated from the following
equation provided that the phase difference between the
current and voltage have been measured:

PF = Cosφ

Answer / ashok

power Factor is the Cosine of the angle between real
power & apparant power
power factor = KW/KVA

Answer / dave.vimal

PF Is

1.Cosine angle between voltage and current.

2.IT IS THE RATIO OF RASISTANCE AND TOTAL INPEDNCE OF THAT
CIRCUIT AND DENOTED BY COS PHI.
P.F. = R/Z
3.RATIO BETWEEN ACTIVE POWER AND APPARANT POWER IS CALLED
POWER FACTOR.

POWER FACTOR= ACTIVE POWER/APPARANT POWER
= VICOS/VI

If the load is inductive,pf is lagging.
If the load is capacitive,pf is leading.
If the load is resistive,pf is unity.
pf can be found out from the power triangle

Answer / ravikumar.g

The cosine of the angle between line voltage and line
current is known as Power Factor.

The power factor calculating the Formula =

PF = RealPower/Apparant Power

PF = KW/KVA

Answer / naresh

power factor is the cosine of the angle between phase
voltage and phase current

Answer / guest

cos

what is the difference between RMS & TRUE RMS VOLTAGE

0 Answers   IIT,

how to check capacitor in general

1 Answers  

i am an maintenance engineer. one distribution board have 5 feeder. recently its ELR trips frequently, but it take some times after trip( 10min,20min..)but 3 feeder no load. two feeder only loaded. i checked one feeder IR value all values are above 50Mohm.but B phase to Earth is only 9Mohm.any problem about low value

0 Answers  

what is max. continous current of LT side of distribtion transformers? ie for25kVA, 63kVA, 100kVA, 200kVA etc

2 Answers  

WHAT IS counter flux IN CT?

0 Answers  

Where is 2 phase supply used commercially?

3 Answers   NTPC,

a.)Ammeter and Voltmeter read rms value or avg. value ? b.)What are symmetrical and Unsymmetrical faults?

2 Answers  

What is the Diference between DYN 11 and DYN 5 .How to change the Vector group from DYN 11 to DYN 5.

3 Answers  

if we going for high voltage usages what are the considering factors, why those factors are effected.... please give me an answer related motor factors like wnidnig, frame, temp etc

1 Answers   ABB,

To prevent the mal operation of a differentially connected relay while energizing a transformer, the relay restraining coil is baised with (a)second harmonic current (b)fifth harmonic current (c)third harmonic current (d)seventh harmonic current

2 Answers  

what is calculation mathod/formaulla for deciding Size of busbar (Copper/ aluminum)for L.T. panel on Various Fault level like 50kA,25kA,10kA

0 Answers   Mega Power,

what should be the ideal gauge of wire (In sq mm) for different loads in Ampere?

0 Answers