A cantilever beam of length L = 3 m carries a uniformly distributed load (UDL) of W = 20 N / m throughout the length. Calculate the bending moment, BM of the beam near the fixed end. What is the shear force, SF at this point? Let SF = -WL, BM = -LWL/2.

1 Answers  

---

Question 52 - The half-life for first order reaction could be described in the differential equation dC / dt = -kC where k is a constant, C is concentration and t is time. (a) Find the equation of C as a function of t. (b) Find the half life for such reaction or the time required to reduce 50 % of the initial concentration, where k = 0.139 per minute. (c) When the initial concentration Co is 16 mol / cubic metre, how long does the reaction required to achieve the final concentration of 1 mol / cubic metre?

1 Answers  

---

What are some good estimates for heat transfer coefficients for coils in tanks?

0 Answers  

---

QUANTUM CHEMISTRY AND CHEMICAL ENGINEERING - EXAMPLE 31.9 : When an algebraic product is defined on the space, the Lie bracket is the commutator [x,y] = xy - yx according to Lie algebra in mathematics. If [p,x] f(x) = px f(x) - xp f(x), p = -ih d / dx, find the value of [p,x] in term of i and h.

1 Answers  

---

What is the wet bulb globe temperature?

0 Answers  

---

ACCOUNTING AND FINANCIAL ENGINEERING - EXAMPLE 34.27 : A biochemical engineering consultancy applies construction accounting in its finance. Its project began on 1 January 2010. Total revenue generated from the project was $9000. On 1 January 2011 as the budget, $2000 had been spent, with $6000 expected. However, the project cost increased latter, causing deviation from its initial budget on 1 January 2012, where $7000 had been spent, with $1400 expected. Let (estimated total cost) = (spent cost) + (expected cost to be spent), (percentage completion) = 100 (spent cost) / (estimated total costs), (total expected profits) = (total revenue) - (estimated total costs). Calculate : (a) total expected profits on 1 January 2011 and 1 January 2012; (b) estimated total cost as and not as the budget; (c) percentage completion of the project since the project began, in the first and second years.

1 Answers  

---

Are there any general rules for flushing slurry lines?

0 Answers  

---

Question 73 - (a) A dryer reduces the moisture content of 100 kg of a potato product from 80 % to 10 % moisture. Find the mass of the water removed in such drying process. (b) During the drying process, the air is cooled from 80°C to 71°C in passing through the dryer. If the latent heat of vaporization corresponding to a saturation temperature of 71°C is 2331 kJ / kg for water, find the heat energy required to evaporate the water only. (c) Assume potato enters at 24°C, which is also the ambient air temperature, and leaves at the same temperature as the exit air. The specific heat of potato is 3.43 kJ / (kg °C). Find the minimum heat energy required to raise the temperature of the potatoes. (d) 250 kg of steam at 70 kPa gauge is used to heat 49,800 cubic metre of air to 80°C, and the air is cooled to 71°C in passing through the dryer. If the latent heat of steam at 70 kPa gauge is 2283 kJ / kg, find the heat energy in steam. (e) Calculate the efficiency of the dryer based heat input and output, in drying air. Use the formula (Ti - To)/(Ti - Ta) where Ti is the inlet (high) air temperature into the dryer, To is the outlet air temperature from the dryer, and Ta is the ambient air temperature.

1 Answers  

---

What industries require filtered compressed air?

0 Answers  

---

BIOPROCESS ENGINEERING - EXAMPLE 14.3 : The kinetic behavior of an enzyme could be described using Michalis - Menten equation : Vo = Vmax [S] / (Km + [S]). Derive this equation from [ES] = [E]total [S] / (Km + [S]), Vmax = Kcat [E]total, Vo = Kcat [ES].

1 Answers  

---

Why LMTD is calculated in Heat -Exchanger problems..Why dont we take average temperature??

4 Answers   Aker Solutions,

---

What is a good device to use for obtaining viscosity data for a non-newtonian fluid?

0 Answers  

---