Answer / mohammad abid shakeel

instrumentation is a technology which deals to measure and
control the industrial process.
application of instruments is also called instrumentation

Answer / sabir ansari

The Technology Of Using Instrument For The Purpose Of
Analyzing,Measuring And Controling The Physical And
Chemical Properties In An Idustry.

Answer / sathish

it is an branch of engineering that deals with measurement, monitoring, controlling of various kinds of energy exchange which take place during process operation

Answer / nisarg patel

Instrumentation is the field of Engineering in which we can measure as well as control the physical & chemical properties like level, pressure, flow, temperature, etc.

Answer / sushil jambhulkar

instrumentation is the science which deal with the study of
instrument. instrument which are use to sense, measure &
control the physical parameter like pressure, temp, flow,
level ,displacement, vibration & more.

Answer / munendra choudhary

INSTRUMENTATION IS THE PHILOSOPHY BASED ON THAT PRINCIPLE-
IF A CONDITION IS CONTROLLED IT MUST BE MEASURED FIRST.

Answer / kishan kr verma

as we know that instrument mean instruments and tation means
automation ,,means that the instruments operated
automatically and give some out put with some specified
inputs ..known as the instrumentation

Answer / balvinder singh

The technology of using instruments to measure and controlling devices, the pyicial properties are called instrumentation.

Answer / chetan jodatti

instrumentation is a reading
which approach's the true
value to the measured
value is called as
instrumentation.

Answer / minisirjam28

instrumantation is a electronic measuring instrument.
like is, guage, varniear calipars, pressor guage,
megger, led. lcd itc.

What is the reason PT speed not incresed in gas turbine?

0 Answers   ROC,

what do u mean by 2/3 soleniod valves?

8 Answers   Nile Sugar,

THE OUTPUT OF A CURRRENT TRANSMITTER OR A PNEUMATIC TRANSMITTER HAS A LIVE ZERO?EXPLAIN

2 Answers  

why most of the DP transmitters using maximum range as 0-2500mmwc?why not 1000 2000 3000 4000mmwc

2 Answers   SPIC, TNPL,

How hart protocol can be connected with control valves?

0 Answers  

A PLC is programmed to drive three motors A, B and C as follows : After running motor A for an hour, motor B should get ON and motor A should get OFF. And after running motor B for an hour, motor C should get ON and motor B should get OFF. And after running motor C for an hour, motor A should get ON and motor C should get OFF. (That is, a cyclic repetition with time period one hour) Now, the second condition is: If any motor gone faulty and is tripped, the consecutive motor should get ON and the faulty (tripped) motor should be eliminated from cyclic repetition. The remaining two motors should bear the cyclic repetition of one hour each. (For healthy motor take logic as high and for tripped motor take logic as low) Now, the third condition is: When motor A load(Amps) exceeds 60% of its rated load, motor B should get ON in parallel to motor A. And when both motors A & B are running in parallel, and if their load exceeds 60% of their rated load, motor C should also start in parallel to A & B. [Here the cyclic repetition is eliminated, until their loads become normal(40%)] [Take logic high(1) for load at 60% and logic low(0) for load at 40%] Now draw a flow chart or a ladder diagram to fulfill the above condition.

0 Answers   MNC,

Describe the basis on which alarms should be generated and how their associated priority is determined

3 Answers  

What are different types of valves?

0 Answers  

Q- Why Phase tester is only used for checking AC not DC ?

1 Answers  

what is the minimum power (P=VI)to produce a spark?

0 Answers  

what is the difference between the microcontroller and PLC?

9 Answers   HAL, Havells,

key phaser where is use and work

0 Answers   BAP,