Answer / virendra

q=discharge=C0 * V0 UNDERROOT(g *2deLTa H)/1-BETA REST TO FOUR

PROCESS DESIGN - EXAMPLE 21.3 : According to a heuristic of chemical engineering plant design, assume a pressure difference dP = 4 psi for each 10-ft rise in elevation. A pump is needed to pump liquid from a storage tank at a lower elevation to a heating tank at a higher elevation with the elevation difference of 60 ft. (a) Find the pressure loss due to such elevation. (b) If the required minimum inlet pressure to the heating tank is 9 psi, with 1 control valve is installed between pump and heating tank, what is the dP minimum required for the control valve and the entrance to the heating tank when the heuristic mentions that at least 10 psi is required for the control valve? (c) The pressure at the inlet of the pump is 8 psi and the flowrate of the liquid produces pressure head of 50 psi. What is the total pressure produced by the pump? (d) Assume a pipeline dP of 2 psi / 100 ft for liquid flow in a pipe according to heuristic, what is the approximate maximum length of the pipe in ft that can be installed between the pump and the heating tank?

1 Answers  

---

Why cavitation is produced

1 Answers  

---

What is maximum recommend pipe velocity for dry and wet gases?

0 Answers  

---

how to calculat suction head in centrifugal pump?

2 Answers   IOCL,

---

Repected sir/Madam, I am goingb to face IOCL technical as well as HR interview, can you forward your hellpfull hand for toward me to sort out my problem by giving some imp interview quetion which is generally asked in chemical industries such like IOCL,HPCL,ONGC,BPCL,RIL,what is the difference in pump,blower & in compressor

0 Answers   IOCL,

---

CHEMICAL FLUID MECHANIC - EXAMPLE 3.1 : Water flows through a pipe with circular cross sectional area at the rate of V / t = 80 L / s where V is the volume and t is time. Let Av = 80 L / s where A is cross sectional area and v is velocity of fluid. For point 1, the radius of the pipe is 16 cm. For point 2, the radius of the pipe is 8 cm. Find (a) the velocity at point 1; (b) the velocity at point 2; (c) the pressure at point 2 by using Bernoulli's equation where P + Rgy + 0.5 RV = constant. P is the pressure, R = density of fluid, V = square of fluid's velocity, g = gravitational constant of 9.81 N / kg and y = 2 m = difference of height at 2 points. The pressure of point 1 is 180 kPa.

1 Answers  

---

Explain what type of pump may be appropriate for a liquid near saturation, a low flow rate, and very limited npsha (net positive suction head available)?

0 Answers  

---

Explain about different types of lamps?

0 Answers  

---

For an ideal black body (A) absorptivity = 1 (B) reflectivity = 1 (C) emissivity = 0 which is true???????

4 Answers   GATE, KFCL,

---

Question 73 - (a) A dryer reduces the moisture content of 100 kg of a potato product from 80 % to 10 % moisture. Find the mass of the water removed in such drying process. (b) During the drying process, the air is cooled from 80°C to 71°C in passing through the dryer. If the latent heat of vaporization corresponding to a saturation temperature of 71°C is 2331 kJ / kg for water, find the heat energy required to evaporate the water only. (c) Assume potato enters at 24°C, which is also the ambient air temperature, and leaves at the same temperature as the exit air. The specific heat of potato is 3.43 kJ / (kg °C). Find the minimum heat energy required to raise the temperature of the potatoes. (d) 250 kg of steam at 70 kPa gauge is used to heat 49,800 cubic metre of air to 80°C, and the air is cooled to 71°C in passing through the dryer. If the latent heat of steam at 70 kPa gauge is 2283 kJ / kg, find the heat energy in steam. (e) Calculate the efficiency of the dryer based heat input and output, in drying air. Use the formula (Ti - To)/(Ti - Ta) where Ti is the inlet (high) air temperature into the dryer, To is the outlet air temperature from the dryer, and Ta is the ambient air temperature.

1 Answers  

---

repected sir i have given gate exam today.......... if i ll get the better rank in that ....what is the next process .....shall i give another one test......or wat....i dint get properlly..... plz help me or mail me on Nish_gasti@yahoo.co.in

0 Answers   IOCL,

---

A cylindrical vessel of 10m height has water upto 6m and is under a pressure of 15bar.What will be the pressure at the bottom most point of the vessel?

4 Answers  

---