we convert 66kv to 33 kv to 11kv to 440v. why can't we
directly convert 33kv to 440 ?
Answers were Sorted based on User's Feedback
Answer / dhaval ahirrao
WHILE CONVERTING THE 66KV TO 440V TWO MAJOR PROBLEMS
ARE THERE;
1 THE TRANSFORMER DESIGN WILL BE VERY CRITICAL.
2 TAPPING THAT ARE NEEDED FOR INDUSTRIES WHICH REQUIRES THE
POWER ABOUT 11KV OR 33KV WE CAN'T PROVIDE DIRECT TO THEM. WE
WILL REQUIRE ANOTHER TRANSFORMER FOR STEP UP
Is This Answer Correct ? | 53 Yes | 8 No |
Answer / siva
converting very high volyage to very low voltage is
impossible because while making the system to convert the
windings in the machine will damage, and the making of 33kv
to 440v the cost very high, and complex
Is This Answer Correct ? | 30 Yes | 14 No |
Answer / k.prakashchandra
440 V supply is for domestic and small industries located at
various places.With 400 V, the lines may extended to max 1
KM considering voltage drop and line losses.33 KV/433V s/s
requires circuit breakers and larger area. Hence can not
erected inside towns along the roads or underground.It is
economical and easier to have 11 KV sub-transmission lines
and 11KV/ 440 V s/s for public utility.
Is This Answer Correct ? | 7 Yes | 1 No |
Answer / peria samy
1. We can step up/down voltage in prescribed format, clearly
says 3:1 ratio of the voltage can step up or down
2.More losses
3.Winding will be damaged
Is This Answer Correct ? | 10 Yes | 8 No |
Answer / narendra nath
Pl.go to internet giving options for 33kv / 433v we can get plenty of suppliers, and also nesco in Odissa using the same, I have seen the transformers.
Is This Answer Correct ? | 3 Yes | 1 No |
Answer / jarvis
In any transformer the power and frequency remains constant.So let the current be 5A(say) then power shall be 66kV x 5A=330kVA. if the voltage is stepped down then the current shall increase in order to maintain the power constant and that amount of current can damage the windings.
Is This Answer Correct ? | 4 Yes | 3 No |
Answer / ammar taqvi
we have to use 66,33,11kv from generation to consumer site just for supply but its not useful for consumer b/c its very high power, that's why we convert it into 440 & 220kv by the help of power transformer, step up/step down for mainly losses.
Is This Answer Correct ? | 0 Yes | 3 No |
Answer / mvk mohan
nice question. If we want 33kv to 440v we can convert by
using step down transformer.bcoz in our site directly
converting 33kv to 440v.depending upon cost.
Is This Answer Correct ? | 13 Yes | 20 No |
Answer / raj
the applicable voltage is 11,33,66,110,220,400 kv like wise for various applications if we covert direct 33 - 440 we didnt get and have to make more expanses 33,11 kv medium voltage uses.
.in power plant electrical design is like wise 440 to 220- 220-11kv or 33 kv ,11-440v aux supply purpose.
in transmission wise step up/step down for mainly losses.
Is This Answer Correct ? | 15 Yes | 29 No |
how the length effects the ampacity of the cable? if a cable is carrying a current of 100A for 50m length then what will the effect on current if we double the length?
Can I parallel 1 MVA generator with 1kVA Generator? if V, F, Ph Seq and Ph angles are same
What is the LUX
what is cogging and crawling
what is a circuit breaker. Weite the types of circuit breaker.
what should be the megger test report for 11KV cable when meggered with 5KV megger , what is the resistance value we should get
waht is the working principle of saft starter & what is the difference in vfd & saft starter
Can u tell me design of switch yard
How many lightning arrestors to be installed on 50MX60MX10M building and is there any formular for that?
in 220/132 substation in place of PT what equipment used & what r the role of that equipment
Why air gap in rotating machines should be small?
what type of motor used to move a 1 ton gate? and relate ratings with load.