In case of 3Phase Supply,
Voltage R-Earth/Neutral - 220
Y-Earth/Neutral - 220
Z-Earth/Neutral - 220
Total is -> 660Volts
Then Why it is said that 3Phase supply is 440
- 6 Answers
- 12787 Views
- Hindustan Unilever Limited, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / sachin mahangade
this voltage measure in R-Y 440v Y-B 440v RB-440 v so this
said that 3 phase R-Y-B supply is 440 v
| Is This Answer Correct ? | 25 Yes | 5 No |
Answer / jmdt
we are calculating in phase to pase oly , so r-y, y-b, b-r
is 440 volt
| Is This Answer Correct ? | 17 Yes | 5 No |
Answer / zubair
in three phase supply there are three phases (here R, y,
and z) and only one neutral.
the voltage between any one phase and neutral is 220.
and the voltage between remaining two phases is 440.hence
the 3 phase supply is 440
| Is This Answer Correct ? | 4 Yes | 1 No |
Answer / padmavathi
If we measure R-Earth/ Neutral that is 1 PH. 3 Phase, 440V
means we have to measure Phase - Phase i.e. R-Y, Y-B, R-B
| Is This Answer Correct ? | 4 Yes | 4 No |
Answer / vinoth
the vole meter have 2 terminals only.... then how can we
mesure in 3 phase voltage... only chance mesure in 2 phases
only the 2 phase voltage 440
| Is This Answer Correct ? | 4 Yes | 5 No |
Answer / n
220 Multiply by root three is equal to 281.4 volts. for 440
volts single phase voltage up to 254 volts.
| Is This Answer Correct ? | 3 Yes | 8 No |
How can I calculate the require lumen of a room. If I use Tube Light (40 W), Or 100 W incandescent lamp. Please give detail answer.
In star delta Schematic can we connect OLR in delta circuit
Transformer Parallel Operations
what is per unit impedance?
What is Procedure the procedure to select CT's & PT's in 66kV and above substation
how much LT load can bear by the 100 KW HT connection.
Sir we have 12.5 MVA(110/11KV) transformer (Y-Y) connected,which tripped showing earth fault,when we charged transformer it stood OK ,but on connecting 11 KV feeders it tripped showing earth fault.our service engineers found that the B phase and R phase phase connecting to neutral broken from HV OLTC(on load tap changer),and R phase and Neutral is ok.Dissolved gas analysis shows that accetline content is high,tan delta value is 12.My dout is it is an internal fault of transformer,why REF or diffrential relay is not acted?
how to find motors H.P. whout any rating? (only give you a motor and multimeter)
What are protection of transformer on HT side & on LT side?
what is the range of using dol starter & star delta starter.
How can we calculate the cable size??? plz give the formula !!!!!
In the N-series schneider reclosers. What is the difference between current during fault time and current at tripping? This appears in the Event log in an event of a trip out.
-
Civil Engineering (5085) - Mechanical Engineering (4451)
- Electrical Engineering (16632)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
