Answer / saravanan.p

In 3 phase 3 wire systems, The line voltage(three wire) is
1.732 (Route 3) times of the Phase voltage (Single wire).

hence line voltage (three wire) = 11 KV.
so phase voltage(single wire) = 11/1.732 KV.
= 6.35 KV.

Answer / veer1981

In 3 phase 3 wire systems, The line voltage(three wire) is
1.732 (Route 3) times of the Phase voltage (Single wire).
hence line voltage (three wire) = 11 KV.so phase voltage
(single wire) = 11/1.732 KV. =
6.35 KV.

Answer / desingurajan

6.35kV

Desingh.M
Rajapalayam
PACR Polytechnic
Ramco Cements

Answer / alpz

And in what way you are planning to measure the voltage of a
single wire. maybe what you mean is the voltage between one
line and ground or neutral. that way the voltage would be
11kv divided by square root of 3. But if you really asking
bout measuring the voltage on 1 wire, it is absolutely zero.

Answer / siddappa & jitendra

actually in ac 3phase system single phase voltage is equal
to line voltage/1.732
=11000/1.732
=6.35kv

Answer / aboli

Vtg.can not be measured with single wire.

Answer / prashanth

voltage is measured between two points.. dat is between to
lines.. in a 3phase the diff between any phase is
11kv..hence it is not confined to a single point.. the
voltage is 11kv betwn ant two lines of 3ph

Answer / sitaram patel

11000/1.73 = 6350volts
we find at single wire voltage.

Answer / b r rajbhar

Its depend on connection mean star or delta connection if star connection to 11kv/1.732 and delta connection same voltage of 3wire 11kv.

Answer / arun kumar

if you know about type of connection then you know that we
use delta delta connection in 11 kv line in which line
voltage keeps same to phase voltage so if youn measure
voltage in single wire then the voltage whoud be same 11kv

Is there any Electrical supervisor license which gives permit to work whole India rather than individual state??

0 Answers  

what is the formula for calculating of dielectric strength of transformer oil.

2 Answers   Bhel,

what is the basis for selection of Protection CT class ? How anyone can decide whether to go for 5P10 or 5P20 ?

3 Answers  

Dear all: Recently we got a question about Interface between PMS and SAP-PM.once we got a update message from PMS.we should set the deletional flag for functional location in SAP system.Is there any FM or BAPI to use?There are only functional location create and change provided by SAP. Best regards!

0 Answers  

WHY TRANSFORMERS ARE RATED IN 11KV 22KV 33KV Instead off 10kv 20kv 30kv

5 Answers  

in the exciter the power is feeded from battry or control or whatever.and we need it in the generators for the stating . do we need it in the shutdown also?i mean the exciter>

2 Answers   Shell,

In the solution of load flow eqation, Newton raphson method is superior to the gauss siedal method because (a)the time taken to perform one iteration in the NR method is less when compared to GS method (b)the number of iterations required in the NR method is more compared to that in the GS method (c)the number of iterations required is dependant on the size of the system in the NR method (d)convergence characteristics of the NR mehod are not affected by the selection of the slack bus

1 Answers  

what is the maximum genarating in india?

17 Answers  

What is meant rectifiers..

1 Answers   MTS,

1 Kva = How many HP

9 Answers  

what is specific gravity of a battery if specific gravity increase/decrease,what will happen to the voltage/current of the battery

5 Answers   NTPC,

what is mean by xlpe cables?

3 Answers