1. Categories >> Engineering
  2. Suggest New Category


Engineering Interview Questions
Questions Answers Views Company eMail

I have a thermal flask in which i have to fill the boiled water. I also have thermocol, saw dust and silver paper. Now tell me how i have to arrange these material to attain minimum heat loss.

 7 7139

Why do we use solid shafts for transfer of power in case of pumps/ turbines & other machines why we use a hollow shaft (pipe) in universal joints of automobiles; although the rated load and twist is approx. the same?

 9 18015

What is the difference between Dielectric and Insulator

 9 29293

i gotadmission in southeast missouri state universit ive got scholarship too my gre is 860 and ielts 6.0 bands and B.E 59.3% with 5 backlogs what are chances that i get visa????/

 1443

how we can varying the speed of dc motor ?

 6 6789

please help me to get the below mentioned quires,which i have to submit for my client.[INSPECTION TEST PLAN] 1]I.T.P for Calibration of all instrument. 2]I.T.P for SS tubing. 3]I.T.P for Fire & Gas devices. 4]I.T.P for CCTV & telecommunication. 5] I.T.P for loop checking.

1 5458

what material is the electrical housing wire made of? is there any difference for the telephone lines?

1461

What is the meaning of utility ground and clean ground? How the distribution panel is grounded?

 2065

A solid body of weight W is placed in a pipe. Suppose water is started flowing through the pipe.what will happen to the body. when it will start flowing ?

BARC,

11 12032

Why electricity is generated and transmitted at the values of multiples of 11?

 3 6207

how to consider the lap length of a bar in IS code.

 7 9941

how the lap length is calculated in reinforcement of 110mm dia steel of Length 15.00 mtrs. & grade of concrete is M20

L&T,

22 99423

please send me syllabus and exam pattern for aptransco(ECE)

Avalon, TATA,

4622

give me the mix proportion for design mix concrete M10 grade 1:4:8

Gammon, IOCL, PSL, SDG, Simplee, STUP Consultants Pvt Ltd,

13 61112

v=r*i this means when voltage increases current also increases at constant resistance.... p=v*i this means when voltage increases current decreases to maintain the power constant which one is true...

 3 4810

Un-Answered Questions { Engineering }

Explain how to design a software ic using vhdl?

646

Tell me the different types of sensors.

620

how can service sitting be setted for MCCB?Example for sittings IR (CURRENT RATING),IS(CURRENT STARTING)IO (current operating

1905

What is the name of this multiplication factors ?

1699

What are to be checked in an induction motor?

1554




What is latching current in scr?

574

The maximum amount of axial load to be applied on a clutch plate is a) 100 KN b) 200 KN c) 300 KN d) 400 KN

1034

What is the maximum operating temperature for a thermoplastic insulated cable?

641

PLZ SEND ME SOME UNIQUE PROJECT OF ELECTRICAL ENG (B.TECH)

1512

Is any generator is developed which is operated with out diesal or other expensive source?

1628

What is used for high speed reading and storing of information in a computer?

557

Dear guys we adding hypo at climax plant and that water is inlet to DM plant so with hypo water that can affect my resins of cation and anion. if it is affect life of my anion and cation so what kind of steps should be take.

1018

What is stepper motor. What is its uses?

647

For the symmetrical continuous beam shown in figure, Prestressed with a force P = 1500 KN along parabolic curve as shown, compute the extreme fiber stresses over the central support for the uniformly distributed load of 24 kn/m. Use load balancing method.

1700

Why synchronous motor is used in power factor improvement,dc series in lift

1179

For More Un-Answered { Engineering } Questions Click Here