Answer / harsimranjot singh

THE OUTERMOST LAYER SHOULD BE THERMOCOL.THEN PLACE THERMAL
FLASK INSIDE THERMOCOL BOX.NOW KEEP THE SAW DUST INBETWEEN
THERMOCOL AND THERMO FLASK AND SILVER PAPER SHOULD BE
APPLIED ON INNER SIDE OF THERMAL FLASK.THUS THE CORRECT
ORDER FROM OUTSIDE IS-
1-THERMOCOL
2-SAW DUST
3-THERMAL FLASK
4-SILVER PAPER

Answer / abhay

for minimising heat losses we should always keep the material with least thermal conductivity ie. highest thermal reistance at the outer most layer and material with highest conductivity
at the imner side sothe correct order from inside is
0>thermal flask
1>silver plate
2>saw dust
3.thermocol

Answer / subhash

thermal flask
saw dust
thermocol
silver paper

Answer / dipak shah

saw dust, thermocol, silver paper

Answer / b.subhash babu

therma flask
saw dust
silver paper
thermocol

Answer / sornakumar

1-THERMOCOL
2-SAW DUST
3-THERMAL FLASK
4-SILVER PAPER

Answer / manikandan

1.Thermal flask,
2.Saw dust,
3.Thermocol,
I think there is no need of silver paper. But as per your
question it cn be used as the last.

Saw dust should be used next to your thermal flask because
it can be tightly packed without air gap than thermocol.

how we convert HP into the KW?

4 Answers  

why we can't use condensate pump in place of feed pump.

1 Answers   Hindalco,

2. Dry saturated steam at 3.5 bar is expanded through a convergent nozzle to 2.2 bar. The exit area is 5 sq. cm. Calculate the exit velocity and mass flow rate, assuming isentropic expansion and super saturated flow. b) A cast iron cylinder head is fastened to a cylinder of 750mm bore with 12 stud bolts. The maximum pressure inside the cylinder is 3 Mpa. The stiffness of part is thrice the stiffness of the bolt. What should be the initial tightening load so that the point is leak proof at maximum pressure? Also choose a suitable bolt for the above application 2 The propeller shaft of a marine engine is to transmit 600 kW at 1200 rpm, without a significant bending. The efficiency of the propeller is 88% at 32 knots ( 1 knot = 1085 km/hr). If the slenderness ratio is less than 50 and the permissible shear stress should not exceed 65 Mpa. Determine the diameter of shaft. 3 A semi-elliptic leaf spring consists of two extra full-length leaves and six graduated length leaves, including the master leaf. Each leaf is 7.2 mm thick and 65 mm wide. The centre-to-centre distance between the two eyes is 1.3m. The leaves are pre-stressed in such a way that when the load is maximum, stress induced in all leaves are equal to 380 N/mm sq. Determine the maximum force that the spring can withstand

0 Answers  

What is reciprocating pump.

2 Answers  

if u have three steam turbine blades, how will u find which blade is for low pressure, high pressure and medium pressure?????

5 Answers   Bhel, Sail,

a three phase squirrel cage induction motor runs slow? list all possible reasons for such fault.

0 Answers  

When we are calculating the heat load sheets,why we are not considering the heat developed from the blood in the human body.Also both men & women can't acess aircondition in same way..women feel too cool even at 22 degree,while men can overcome that.

0 Answers   DVC,

what is the material of radiator sleeves or mesh?

0 Answers  

What is the problem use octane in petrol Engine?

2 Answers   MAHINDRA,

If a welder qualified for 2G,3G&4G positions,then is he automatically qualified for 6G position?

2 Answers   GMR,

What are thermal neutrons ?

0 Answers  

In a reaction turbine,where the pressure drop will be in fixed blade or moving blade?

3 Answers