1.wat is the purpose (or)function of regulator?

2.wat is the purpose of stabiliser?

Answers were Sorted based on User's Feedback



1.wat is the purpose (or)function of regulator? 2.wat is the purpose of stabiliser?..

Answer / silamparasan p.

Function Of Regulator: Regulator is a device is used to
control the speed by variying the input voltage.

Function Of Stabilisher: Stabilisher is a device used to
stabilise the supply voltage from low voltage or voltage
high voltage to a electronic system like T.V, Fridge, etc.
But in stabilisher we can not vary the voltage.

Is This Answer Correct ?    13 Yes 1 No

1.wat is the purpose (or)function of regulator? 2.wat is the purpose of stabiliser?..

Answer / shaik

Regulator is a devise which regulates the voltage of one
value to the other.
eg:a voltage of 12v with disturbances is fed to a regulator
like IC 7805 then the output voltage will be 5v fixed.

Stabilizer is a devise which provide constant output voltage
even during the fluctuations.

Is This Answer Correct ?    7 Yes 0 No

1.wat is the purpose (or)function of regulator? 2.wat is the purpose of stabiliser?..

Answer / kumar

In regulator we can get the vary output voltage ,
In stabiliser we can get only constant output voltage

Is This Answer Correct ?    8 Yes 2 No

Post New Answer

More Electrical Engineering Interview Questions

what will be the effect on the voltage .if power frequency is increasing or decreasing.

2 Answers  


what is ceiling voltage in an exciter?

1 Answers   KEPCO Energy Service Company,


onan full form

5 Answers  


What is meant by IP55 motor.Where it is used?

2 Answers   Zuari,


To have variable speeds we use a. Induction motor b. Traction motor c. Shunt motor

1 Answers  






why the autotransformer burnt while stating the pumpmotor?, In starter and motor there was no abnormality.

4 Answers  


what is the effect of back reactive power on the generator ?

0 Answers   MRF,


control wiring purpose,standards, ferrule code standard, interlock, schematic, symbol

1 Answers  


what should be the megger test report for 11KV cable when meggered with 5KV megger , what is the resistance value we should get

7 Answers  


A.V.R maintains the voltage of a generator when it is in island mode but when the generator is synchronised with grid it maintenance the P.F,how it happens please any body explain it in detail.

2 Answers   TATA,


If there is unit power factor in a power house and a capacitor bank used in a factory at resistive load . In this case, will there leading power factor in power house across that factory.

2 Answers  


1. Synchronization is not required A. Thermal B.Hydel C.Wind D.Nuclear

2 Answers   APGenco, Birla Power,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)