What will the new flow factor if D/P Transmitter is RE-RANGED from 25" WC

What will the new flow factor if D/P Transmitter is
RE-RANGED from 25" WC to 50" WC

Question Posted / gayash khan

3 Answers
9105 Views
ADMA OPCO, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

What will the new flow factor if D/P Transmitter is RE-RANGED from 25" WC to 50" WC..

Answer / carl_ellis

Answer:
The flow rate at 50.0"wc will be 141.4% of the flow rate at
25.5"wc.

Reason:
The design maximum flow rate at 25.0" is 100.0% flow rate.
Flow rate is the square root of the percentage of flow at a
given DP.
The flow rate at 25.0"w.c. DP is the square root of 1.00 (or
100%)

If the DP doubles from 25.0 to 50.0, then the DP increases
from 100% at 25.0"wc to 200% at 50.0"wc
The flow rate at 200% DP increases by 141.4% because the
square root of 2.00 (or 200%) is 1.414.

Carl Ellis
Measure First

Is This Answer Correct ?

7 Yes

0 No

What will the new flow factor if D/P Transmitter is RE-RANGED from 25" WC to 50" WC..

Answer / enka group iraq

Ans;- A simple calculation is as follow :- Q1 / Q2 = √DP1/√dp2
Q1= Q2 X √DP1/√dp2
Q1 = new flow factor, Q2 = existing flow factor
DP1 = transmitter new range DP2 = transmitter existing range
Q1 = Q2 X √50/25 = Q2 X 1.41
The new flow factor will be 1.41 times higher then the existing flow factory

Is This Answer Correct ?

1 Yes

0 No

What will the new flow factor if D/P Transmitter is RE-RANGED from 25" WC to 50" WC..

Answer / selva

The ratio of
New factor New range
---------- = -----------
Old factor Old range

Is This Answer Correct ?

0 Yes

2 No

Post New Answer

More Instrumentation Interview Questions

I m appointed as an automation trainee engineer in small firm in that I am only the one , my company give me a project on s7-200 as i m beginner I don't know how to program so please send me the helpful site so that I complete my project before deadline....please help me out in this critical situation.

0 Answers

Lux meter is the measuring device to measure the lux level of lighting fixture. in industrial sector two types of lighting fixture is being used as street lighting purpose 1. HPSV (Sodium) and 2. HPMV (Mercury). HPMV having white light which is an combination of red, blue and yellow colour, while HPSV haivng Yellow lighting. in HPSV red & blue colour will be absent. during measurement of the lux level of HPSV and HPMV fixture. 1. Lux meter can measure the actual lux level of both fixture? 2. or it will show false reading for HPSV fixture light as it has only yellow light present. please give me answer

0 Answers Ace Info,

Please asked me How calculate DCS controller memory.

0 Answers Yokogawa,

Hi my friends Is any one who can assist me in knowing the typical interview questions for system engineer at General Electric pty Ltd

0 Answers

IS there any effect of vortex in low pressure side of the transmiter after the orific in feed water line? if yes then what is the calculation?

0 Answers

what is the procedure for auto tune in masoneialn 12300 series displacer type transmitter?

0 Answers

my data card only does run in my mobile so how can change it that it run other mobile & computer and i can stor data in my data card

0 Answers

What does threshold mean? what does tolerance mean?

1 Answers DEWA,

what is the diffrence between pressure safety valve & pressure relief valve....pls

0 Answers Oil India,

I installed the smartplant instrument v8, but can not be opened, that always said: "INTools 2007 hardlock no found". So Could you help me how to do for that?

0 Answers SRAAC,

how eddy current loss in probe and induced gap voltage accros probe trip and shaft

1 Answers Reliance,

i want to Measure the Difference pressure of Packed distillation Column of height 3 mtr. h.p. side connected to bottom & L.P. side connected to the top , so tell me what will be THE URV & LRV of that D.P. transmitter?

5 Answers

For more Instrumentation Interview Questions Click Here