Interested to Buy Any Domain ? << Click Here >> for more details...
difference between unilateral tolerance and bilateral
tolerance
- 7 Answers
- 77261 Views
- Dover, Focus Energy, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / mustafa
A unilateral tolerance is tolerance in which variation is
permitted only in one direction from the specified direction.
eg 1800 +0.000/-0.060
bilateral tolerance is tolerance in which variation is
permitted in both direction from the specified direction.
eg 1800 +0.060/-0.060
| Is This Answer Correct ? | 249 Yes | 31 No |
Answer / chandan sharma
In bilateral tolrence the limit dimensions are given above and below the the nominal or basic size,and in uniletral tolrence system the limit dimensions are onlyabove or below the nominal size.
| Is This Answer Correct ? | 80 Yes | 10 No |
Answer / prakash
In bilateral tolerance the limit dimensions are given above and below the nominal size
In unilateral tolerance the limit dimensions are given only above or below the nominal size
| Is This Answer Correct ? | 60 Yes | 8 No |
Answer / precious
Unilareral Tolerence Is The Tolerence Where Limits of Dimensions Are Specified For One Side Of The Basic Size And Bilateral Tolerence Is The Tolerence Where Limits Are On Both Sides Of The Basic Size.
| Is This Answer Correct ? | 26 Yes | 6 No |
Answer / manojkumar k a
A toleranced dimension is bilaterial if the limit dimensions are given above and below the nominal size
When the two limit dimensions are only above the nominal size or only below the nominal size then the tolerance are said to be unilateral
| Is This Answer Correct ? | 4 Yes | 1 No |
Answer / rasik prajapati
15.30 +0.02/+0.05 is this unilateral or bilateral ?
please help with feedback with logic.
| Is This Answer Correct ? | 6 Yes | 3 No |
Answer / rathn kumar
Consider a shaft, if its ok if u give value,and -value,(any one at a time) if it works in that way, then it is the bilateral tolerance;
If only one way the shaft going to be fitting, let it be in value case, and not in -value case , then it is the unilateral case. Is it the answer?I think so!
| Is This Answer Correct ? | 2 Yes | 8 No |
what is counter weights. Why the ship cranes are not having counter weights irrespect of industrial & civil construction cranes are having counter weights.
How to calculate IKW (inputkilowatt) ie.. efficiency of a airconditioning chiller plant capacity of 310TR
wap to insert an element in array at a particular location
how to calculate duct fittings surface area ?
What is g.i.?
What are the defects in exhaust valve?
i am very much confused about direction of thrust in steam turbine...we have steam turbine of 13 stages,10 stages of impulse and 3 of reaction type....in study manual direction of thrust is towards inlet but on thrust bearing its loading side is towards condenser(exhaust side) wile also dummy ring is present in design which also restrict rotor to move in exhaust side direction not inlet ....
What is the difference between isotropic material and homogeneous material ?
How a main gate (steel) get support from top whlie slides on the rail fixed on the bottom surface??
differentiate pressure relief valve and pressure saftey valve
Why cavitation will occur in centrifugal pump and not in displacement pump?
How do you check steering gear
-
Civil Engineering (5086) - Mechanical Engineering (4453)
- Electrical Engineering (16638)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
