what is the unit of hardness?

Categories >> Engineering >> Mechanical Engineering
Suggest New Category

Question Posted / rohit mathanker

21 Answers
38501 Views
Novatex, NTPC, Suzlon, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

what is the unit of hardness?..

Answer / qasim ahmed

The unit of hardness can be measured by it hardness number
with the help of (Brinell hardness number and Rockwell
hardness number)

Is This Answer Correct ?

74 Yes

5 No

what is the unit of hardness?..

Answer / jayesh

it also defined by number(hardness number).

Is This Answer Correct ?

34 Yes

6 No

what is the unit of hardness?..

Answer / abhijit

unit of hardness is Rockwell hardness number and Brinell
hardness

Is This Answer Correct ?

15 Yes

2 No

what is the unit of hardness?..

Answer / guest

HRC,HRB

Is This Answer Correct ?

18 Yes

7 No

what is the unit of hardness?..

Answer / abdul rahim

GENERALLY HARDNESS IS COMPARED WITH THE STANDARD METAL
(DIAMOND)WHOSE HARDNESS IS EXTREME SAY 100.BASED ON THE
HARDNESS PROPERTIES IT CAN BE EXHIBITED IN brinell hardness
(HB),rockwell hardness(HRC),VICKMERS INDEX

Is This Answer Correct ?

8 Yes

1 No

what is the unit of hardness?..

Answer / kuldeep

hardness no. of Water is in UNIT of PPM
Material Hadrness is measured into Brinnel hardness Number

Is This Answer Correct ?

6 Yes

0 No

what is the unit of hardness?..

Answer / rohit

it is define by number like brenell hardness number and
vicker hardness number

like copper(annealed) = 45HV
COPPER (HALF HARD)=85HV

HERE HV REPRESENTED VICKER HARDNESS NUMBER

FOR KNOW METHOD REFER SOM BY R K RAJPUT

Is This Answer Correct ?

5 Yes

0 No

what is the unit of hardness?..

Answer / mukesh kumar

Brinell hardness number and Rockwell hardness number.

Is This Answer Correct ?

4 Yes

1 No

what is the unit of hardness?..

Answer / om

Depends upon the test performed. However the hardness is
designated by some number. If Brinell Hardness Test is used
then hardness-number is followed by BHN.For Rock-well test
it is denoted by HRC,HRA,HRB etc.

Is This Answer Correct ?

2 Yes

0 No

what is the unit of hardness?..

Answer / devendra patil

HRB

Is This Answer Correct ?

6 Yes

5 No

Post New Answer

More Mechanical Engineering Interview Questions

WHAT IS A TR REQUIRED IF AIR FLOW 6500 CMH COIL INLET TEMP 7 - 12 DEGREE C AIR TEMP INLET - 18 DEGREE C & REQUIRED TEMP IS 12 DEGREE C

0 Answers TATA,

Is a diesel engines maximum rpm limited by the diesel burn rate?

0 Answers

WHY THE WELDING JOB IS MAKE NEGATIVE IN MIG WELDING

2 Answers JSW, TATA,

What are the most immediate challenges of this position that need to be addressed in the first three months?

1 Answers Petro Star Mount,

relation between head,capacity & rpm

1 Answers

What is the purpose of increasing the pressure on the F.O. system of the engine?

0 Answers RRB,

How do you detect earth by lam p?

0 Answers RRB,

What is the difference between blower and fan?

0 Answers

Escape Velocity of Earth is

2 Answers Bhel,

i am prepared for the rrb section engineer, please help me to guide , how to prepare and which books are good for technical, aptitude(arthimetic, resonning and g.k), send details to me by email: sudhakar.gudditi@gmail.com

1 Answers

type of welding

0 Answers

If a cantilever beam is loaded with point load at its free end and when the load increases at which section it will break first?

5 Answers Government, TATA,

For more Mechanical Engineering Interview Questions Click Here