Answer / arvind singh

There is not any technical name for the transformer oil,
its only the specification which made the crude oil to
transformer oil(insulating oil). Nepthanic oil, Peraphenic
oil, Mineral Oil (its the specification which process the
crude oil to the nepthane base for the cooling of
transformer which have various acceptance norms as
specified in IS:335 below
Sl No. Characteristics Requirement Method of test as
per latest revision of IS as indicated below
1. Appearance The oil shall be clear and
transparent and free from suspended matters/sediments A
representative sample of oil shall be examined in a 100 mm
thick layer at the ambient temperature
2. Density at 29.5 Deg. C. Max. 0.89 g/cm3
IS:1448[P:16]
3.
Kinematic Viscosity at 27oC Max. 27 cst
IS:1448[P:25]
4. Interfacial tension at 27oC Min. 0.04 N/m
IS:6104
5. Flash point Pensky Marten (closed),Min.
140oC IS:1448[P:21]
6. Pour point Max. -6 deg. C IS:1448[P:10]
7. Neutralisation value (Total acidity) Max.
0.03 mg KOH/G IS:1448 [P:2]
8. Corrosive Sulphur Non-corrosive IS:335
9. Electric Strength (breakdown voltage)
IS:6792
a) New unfiltered oil, Min. 30 kV (rms)
b) After filtration, Min. 60 kV (rms)
10. Dielectric dissipation factor (Tan delta) at 90º C,
max. 0.002 IS:6262
11. Specific resistance (resistivity)
IS:6103
a) at 90oC min. 150x1012 ohm-cm *
b) at 27oC min. 2500x1012 ohm-cm *
12. Oxidation stability IS:335
a) Neutralisation value after oxidation Max.
0.40 mg KOH/g
b) Total sludge value after oxidation Max.
0.10 percent by weight.
13. Presence of oxidation inhibitor present by weight
The oil shall not contain anti-oxidant additives
IS:13631
14. Water content maximum 50 ppm IS:13567
15. Aging characteristics after accelerated ageing
(open beaker method with copper catalyst)
IS:12177
Method A
a) Specific resistance (resistivity) Min.
IS:6103
1) at 27oC, Min. 4.5x1012 ohm-cm
2) at 90oC, Min. 0.2x1012 ohm-cm
b)Dielectric dissipation factor (Tan delta) at 90oC
Max.
0.20 IS:6262
c) Total acidity, Max. 0.05 mg KOH/gm IS:1448
[P:2]
d) Total sludge, Max. 0.05 percent by weight
Annex A of IS 12177
16. SK value, max. 4-8% volume increase IS : 335

Answer / ajit

Askarel

Answer / kamal

pure hydrocarbon minreral oil

Answer / maganti hari krisha

escral

Answer / gokulakrishnan

Transformer oil, or insulating oil, is usually a highly-
refined mineral oil that has excellent electrical insulating properties.

Answer / manoj

it is a byproduct petroleum oil.

Answer / nage

No such name but can you tell me what IP/ASTM/any other
thermometer is used to maintain 27 deg C of KV bath?

Answer / a k singh

Poly Chlorinated Biphenyl (PCB) or Askerials.

Answer / sanjeev

TRANSFORMER OIL NAME
TECHINICAL NAME IS CRUDE OIL' BUT
ACCORDING TO BOSS LUBRICANT' CANADA
THE CHEMICAL NAME OF THIS OIL IS
SEVERELY HYDROTREATED HEAVY NAPHTHNIC DISTILLATE(SHHNH)......
..;;;;;;;;;;;;;
:-)

Answer / thanigai1984

Electro mineral oil ...

what is the formula to calculate voltage drop/loss on 66KV Transmission Line?

0 Answers  

What is the formula formula for Busbar sizing and what are the things to be consider for Busbar Calculation?

0 Answers   ABB, APL,

the winding of Gen and Motor is star or in delta ??? and why

1 Answers  

Is there any problem about which the drive (inverter) doesn't show/display the alarm and/or fault but instead of this , it doesn't work ? I want to know that could there be any kind of problem in the drive when the drive doesn't display the alarm and/or fault ?

0 Answers   Siemens,

How to protect a Dosing pumps/any sensitive equipment (single phase) from surge protection inside a food factory.

0 Answers  

what is corona effect

3 Answers  

what is the tolerance for the magnetic balance test conducted on the distribution transformer?

0 Answers  

Can you explain operating principle of Inverse Definite Minimum Time” (IDMT) relay

2 Answers  

Is ground earthing required for neutral conductor of a prime mover ie DG set?

1 Answers  

Why induction motors draws higher current during starting condition?

1 Answers  

whenewher three phase supply is given to induction motors revolving/rotating field is created & rotor rotates.When the three phase supply is given to three phase transformer then revolving,/rotating field is created or not? if not why?

1 Answers  

What is the name and type of power transformer oil?

4 Answers