-
Civil Engineering (5085) - Mechanical Engineering (4451)
- Electrical Engineering (16632)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
What kind of Neutral CT can be placed in 11/0.433KV transformer to be used and what are its specification?
1400Dear all,recently in our plant we installed a conveyor for this the motor ratings are 5 hp and Amps 7.39.Due to on urgent starting of conveyor we fix the DOL starter with range of 9-15 amps.give me suggestion regarding on this issue
1 1717Question 99 - (a) The quantum number m is given by m = -s, -s + 1. If s = 0.5, find the values of m. (b) | T > = (cos T) | V > + (sin T) | H >. The V and H states form a basis for all polarizations. Let cos T = 0.8. (i) If (sin T)(sin T) + (cos T)(cos T) = 1, find the value of sin T. (ii) For | T > = a | V > + b | H >, where a x a represents the probability of | V > and b x b represents the probability of | H >. Which one is more abundant, | V > or | H >? (iii) Find the value of T without using any mathematical tools.
1 1540do we consider shrinkage factor for calculating cement consumption for CM mixes for different works?
1226I have energy meter for educational project having 0.5s class but my friend need 0.2s class meter , which one is good for that purpose and what is the actual difference of that two classes , need very easy example also.??
BBS,
985In an existing power plant (phase I) with step up transformers (3nos) with Ynd1 vector group to the 400KV bus bar,an extension power plant (phase II) with transformers (4nos) with Ynd11 vector group >. what are the consequences of such configuration ,please note that % impedance are also differ i.e. 15% & 10.5% the reason was that auxiliary supply interface is at different voltage levels i.e 400v & 6.6KV in phase i and phase II respectively .please advise ! Thank you !
1 1335I am experienced with house and industrial wiring but I don't have any licence how can I apply an licence and which type of licence i can get i didn't complete deee just only experience
1205
Normally in slabs, steel quantity is not added when you calculating concrete quantity for that slab, why it is not added ?
we use 400/5A ct and 35/roor3KV,/0.1/root3KV,0.1/root3KV pt ratio. What is the multiple factor of this meter.
what is your majour contributions in your present job
Can you discuss a situation where you managed supply chain challenges that impacted production schedules?
What is the angle of repose?
Vibromotor 252MV 1/4HP2P..what is mean by 252MV?
What is the formula for selecting the cabels according to load? How to calculate what sq.mm cabel to be used?
Define Octane number and Cetane number
Why should a chain drive be used over a belt or rope driven drive? State pro`s and con`s?
Define gain margin?
Why upper weighing limit of electronics balance is 90% of the total weighing capacity?
What is the exact minimum vale of voltage between an earth and netural which can damage or can do malfunction of the electronic equipments ? If this is mentioned in any book, pl.give reference.
What are your personal skills and abilities for such a Master Course and your possible preparation to undertake this course?
we are having yokogawa centum cs3000 dcs in our power plant. i need some of the operator guides NOT to appear in HIS0163 AND HIS 0162 but it shoul appear in HIS0164 HOW TO DO IT?
Define chroma?
