Engineering Interview Questions
Questions Answers Views Company eMail

What are the procedures on how to anneal?

RRB,

786

How many percent (%) of carbon content in Cast Iron?

Sail, RRB,

6 6415

What will happen if the centrifugal pump has no pressure?

RRB,

2 2578




What are the things to do when approaching the port?

RRB,

802

Give the safety precaution when working in a high place.

RRB,

890

Checking points in steering gear system?

RRB,

759

What are the procedures in paralleling D/G?

RRB,

873

What is the indication of leaking starting valve of an engine?

RRB, Maruti Suzuki,

1 1006

What will be the cause of high temperature in one cylinder of D/E?

RRB,

773

What is the purpose of air cooler of D/E?

RRB,

865

How are voltmeter and am meter connected in the circuit?

RRB,

773

What is the function of space heaters for motors?

RRB,

2 5069

What is Ohms law?

RRB,

1 1870

Enumerate the parts of Main Switchboard

RRB,

828

Examples of good conductors of electricity.

RRB,

1 1062







Un-Answered Questions { Engineering }

which metal is use in shunt

3300


what will be the minimum bearing clearance that after it will not profitable for machines?

1114


A PLC is programmed to drive three motors A, B and C as follows : After running motor A for an hour, motor B should get ON and motor A should get OFF. And after running motor B for an hour, motor C should get ON and motor B should get OFF. And after running motor C for an hour, motor A should get ON and motor C should get OFF. (That is, a cyclic repetition with time period one hour) Now, the second condition is: If any motor gone faulty and is tripped, the consecutive motor should get ON and the faulty (tripped) motor should be eliminated from cyclic repetition. The remaining two motors should bear the cyclic repetition of one hour each. (For healthy motor take logic as high and for tripped motor take logic as low) Now, the third condition is: When motor A load(Amps) exceeds 60% of its rated load, motor B should get ON in parallel to motor A. And when both motors A & B are running in parallel, and if their load exceeds 60% of their rated load, motor C should also start in parallel to A & B. [Here the cyclic repetition is eliminated, until their loads become normal(40%)] [Take logic high(1) for load at 60% and logic low(0) for load at 40%] Now draw a flow chart or a ladder diagram to fulfill the above condition.

1049


What is the simplest formula to calculate the rotor diameter of a synchronous generator?

1126


how much cement and sand required for 1cum rr masonry

3586






Aptitude, reasoning, quants, verbal and technical question

233


Re: Sugar Cane Bagasse What are the 1. Specific Heat of Bagasse at 50% moisture, 40% moisture and 25% moisture? 2. What is bu;lk density of bagasse at 50% moisture, 40% moisture and 25% moisture? 3. What is specific gravity of bagasse at 50% moisture, 40% moisture and 25% moisture? 4. What is the specific heat of flue gases generated from boiler fuelled by bagasse? 5. What is the specific gravity of flue gases generated from boiler fuelled by bagasse?

8054


as per is code, what is the minimum content of opc and ppc cement for rcc structure

1027


can you give me example of igbt drive circuit... i still not under stand how it can be design with certain equation using mathlab program...

975


When we need up only in o/p 440v, so why we use directly in 11kva in input?

594


any one please tell taht what type questions will be asked in BHEL interview, i am having interview on 24th Dec, please send this to mail pradeepsistam@yahoo.co.in

792


how to find ssm in foundation?

657


what is the eligibility criteria of mico bosch

2110


what is the procedure to start the turbine?

1356


I have 1500/1A CT If i connect this CT in 6.6KV bus bar means what will be the voltage present in CT?

777