What are characteristics of UDP A. It is reliable and acknowledged B. It is unreliable and acknowledged C. It is reliable and unacknowledged D. It is unreliable and unacknowledged
2 3731Given the following IP address from the Class B address range 172.35.21.12. Your network plan requires no more than 126 hosts on a shored. Which value should you use as the subnet mask? A. 255.255.0.0 B. 255.255.128.0 C. 255.255.126.0 D. 255.255.255.128 E. 255.255.255.252
5 8526At which layer of the OSI model does the ping command operate? A. session B. network C. transport D. maintenance
12 43162Which command displays the IP addresses assigned to specific host names? A. show hosts B. show interface C. ping host name D. config host name E. show host mapping F. show host ip address G. trace ip addresses host name H. a partridge in a pear tree
2 4122What is the connection oriented protocol in the TCP/IP protocol stack? A. IP B. UDP C. TCP D. DNS E. OSPF
HCL,
5 9007Which two statements accurately define IP addressing rules? (Choose two) A. IP multicast addresses start with 240 B. A host Carbon of all 1 a indicates a network broadcast C. The value of zero (0) in the host Carbon means all hosts on the network D. IP addresses are four octets long and contain a network Carbon and a host Carbon
2 7016Which network mask should you place on a Class C address to accommodate a user requirement of two subnetworks with a maxximum of 35 hosts on each networks A. 255.255.255.192 B. 255.255.255.224 C. 255.255.255.240 D. 255.255.255.248
4 8100What are two characteristics of the RARP protocol? (Choose two) A. it generates parameter problem messages B. it maps IP addresses to Ethernet addresses C. it maps Ethernet addresses to IP addresses D. it is implemented directly on top of the data link layer
1 6783Which command verifies encapsulation as well as Layer 1 and Layer 2 statistics on a router configured for Frame Relay? A. show ip B. show interface C. show statistics D. show frame-relay
1 3673Which configuration mode and command combination sets the bandwidth metric of a Frame Relay connection? A. router(config)# clock rate 56 B. router(config)# bandwidth 56 C. router(config)# bandwidth 56000 D. router(config)# clock rate 56000
2 4656What must you do to test connectivity on a dial on demand routing (DDR) link? A. increase the idle Import parameter B. send interesting traffic across the link C. reboot one of the integrated services digital network (ISDN) routers D. reset the DDR integrated services digital network (ISDN) router statistics to zero
1 6456Which two statements about integrated services digital network (ISDN) are true? A. ISDN provides data only capability B. ISDN provides an integrated voice/data capability C. The ISDN standards define the hardware and call setup schemes for end the end digital connectivity D. Users receive more bandwidth on WANS with a leased lin of 56 Cops than with multiple B channels
1 4224You are conferring a Frame Relay router with subinterfaces on interface Serial 0 Which subinterfaces numbers could you use for this configuration? A. 1 and 2 B. 0 2 and 0 3 C. 1 0 and 1 1 D. 0 1 a and 0 1
1 3117Which element is used to define the rate in bits per second that a Frame Relay switch agrees to transfer data? A. clock rate (CP) B. Committed Information Rate (CIR) C. Local Management Interface (LMI) D. data link connection identifier (DICI) E. Committed Rate Measurement Intercal (CRIMI)
2 7118Which range of possible numbers do standard ipx access lists have? A. 100 199 B. 600 699 C. 800 899 D. 1000-1099
1 3580
Name the command we use for ping in ipv6?
How does PPTP encapsulate data?
What is cisco?
What does eq means?
What are the different types of passwords that you can use in cisco routers?
Can you define LAC
Tell me which cable called roll-over?
What is BootP?
Which command we give for see routing table?
Which type of transmission bus topology support?
Explain what are the ranges of private ips?
How much hold down time of eigrep protocol?
What is the difference between csma/cd and csma/ca?
Default packet size of ipv6?
When we use loop back ip?