Interested to Buy Any Domain ? << Click Here >> for more details...
Identify the command to determine if CDP is enabled? A.) show enable cdp B.) show cdp enabled C.) show cdp run D.) show cdp
1 3780Which 2 commands shows the Cisco IOS filename? A.) show IOS B.) show ver C.) show flash D.) show mem E.) show NVRAM
1 4477Identify the command to copy a configuration file from a TFTP server to a routers active configuration? A.) Router# copy running-config tftp B.) Router# copy tftp running-config C.) Router# copy tftp 172.16.0.1 running-config D.) Router(config)# copy tftp running-config
1 4939Identify the command mode necessary to enter the extended ping command? A.) Router# B.) Router> C.) Router(config)# D.) Router(ext-ping)#
1 4998Identify the command to configure the router for IGRP autonomous system 100? A.) Router(config)# router igrp 100 B.) Router> router igrp 100 C.) Router# router igrp 100 D.) Router(config)# router igrp
CMS,
3 7276Identify the command that forces the router to load into ROM mode upon a reload? A.) boot system rom B.) rom boot C.) boot system flash rom D.) boot router rom
1 4491Identify the command that specifies Serial 0 in slot 1? A.) Router(config)# interface serial1/1 B.) Router(config)# interface serial1/0 C.) Router(config)# interface serial0.1 D.) Router(config)# interface serial0/1
1 5241Identify the command to configure the configuration-register? A.) Router# config-register 0x2102 B.) Router(config)# config-register 0x2102 C.) Router(config-reg)# 0x2102 D.) Router> config-register 0x2102
1 4242Identify the command to disable CDP on an interface? A.) Router(config-if)# no cdp enable B.) Router(config-if)# no cdp run C.) Router# no cdp enable D.) Router(config-if)# no cdp
1 5708Identify the command that will display the RIP routes entering and leaving the router? A.) Router(config)# debug ip rip B.) Router# debug ip rip C.) Router>debug ip rip D.) Router# debug rip routes
ABC,
1 3921Identify the prompt displayed if in privileged exec mode? A.) Router(config)# B.) Router# C.) Router> D.) Router(priv)#
2 7629'Show cdp neighbors detail' show the following 3 pieces of information? A.) Hardware platform B.) Software version C.) Same as 'show version' command D.) Up to 1 address for each protocol E.) Non-direct connected routers
2 7039Identify the command mode necessary to enter the standard ping command? A.) Router(config)# B.) Router> C.) Router(std-ping)# D.) Router(config-if)#
2 5958Identify the command to run 'setup'? A.) Router(config)#setup B.) Router?setup C.) Router#setup D.) Router>setup
1 5530Identify the command that configures serial0 for PPP encapsulation? A.) Router(config)# encapsulation ppp B.) Router(config-if)# encapsulation serial ppp C.) Router(config-if)# encapsulation ppp D.) Router# encapsulation ppp
2 6964
What does aaa stands for?
Which multicast ip eigrp protocol use?
Explain why is udp lease favored when compared to tcp?
Utilizing RIP, what is the limit when it comes to the number of hops?
How many ports are present in a router?
Explain which layer are called upper layer?
Tell me how many reserve ports?
hi shain can u send me some detail about bgp so that i can enhance my knowledge over bgp and can you also teach me about the process of suppernating. now what i am thinking that this could be last visit on that site overhere.so please mail that short of thing on my gmail id i am requesting to all of the visitor that please send theire doubt or question to my new gmail id which is jitendera.ccnainterview@gmail.com.i will try to solve it if i am capable to do it Wishing all of you for great future Jitendera kaumar sinha
What are the different types of network in ccna?
Define osi?
Explain how many tables are in ospf protocol?
Why mac address called physical address?
What is the maximum request timer?
Which type of transmission bus topology support?
How does Hold-downs work?
