Interested to Buy Any Domain ? << Click Here >> for more details...
Station A is transmitting data to station B faster that station B can handle it. When station B's buffer fills up, it send out a message to station A to stop sending data. After B empties out its buffer, station B sends a message to station A to start sending data again. This is most directly an example of (pick the best answer only): A.) Poison Reverse B.) Connectionless protocol C.) Windowing D.) Connection oriented protocol E.) Flow Control F.) Split Horizon
1 6048The Integrated Services Digital Network (ISDN) Basic Rate Interface (BRI) provides which of the following? A.) 1.544 Mbps B.) 23B + 1D Channel C.) 24B + 1D Channel D.) 2B + 1D Channel E.) 23B + the Disney Channel
2 5015Which layer manages protocol access to the Network layer? A.) Datalink - MAC Sublayer B.) Datalink - LLC Sublayer C.) Transport D.) Session E.) Network
3 6667Identify the command to display the IP routing table? A.) show route B.) show ip route C.) show ip table route D.) show ipx route
1 5315Identify the command to display all the valid commands at the given mode? A.) Help all B.) Help C.) All commands D.) ?
3 5566Identify the keystroke used to terminate the setup mode? A.) Ctrl-K B.) Crtl-C C.) Ctrl-Z D.) Crtl-End
1 8851Identify the command to display the IP host table? A.) show ip hostnames B.) show ip names C.) show hosts D.) show ip hosts
1 6184Identify the command to display the configured IP routing protocols? A.) show protocols B.) show protocols all C.) show routing-protocols D.) show ip protocols
2 6221Identify the command to configure ALL the default VTY ports? A.) Router(config)# line vty 0 4 B.) Router# line vty 0 4 C.) Router(config)# line vty D.) Router(config)# line vty 0
2 5709Identify the command to reload the router? A.) Router(config)# reload B.) Router# reset C.) Router# reload D.) Router> reload
1 6663Identify command that configures 'Cisco1' as a secret password? A.) Router(config)# enable secret password Cisco1 B.) Router(config)# enable secret cisco1 C.) Router(config)# enable password Cisco1 D.) Router(config)# enable secret Cisco1
2 6606Identify the statement which connects access-list 101 inbound to interface e0? A.) Router(config-if)# ip access-group 101 in B.) Router(config-if)# ip access-group 101 C.) Router(config)# ip access-group 101 e0 in D.) Router(config)# ip access-group 101 e0 in
1 4467Identify the command that displays ethernet0/1 interface status? A.) show interface ethernet0/1 B.) show interface ethernet e0/1 C.) show interface ethernet0.1 D.) show ethernet0/1
3 7177Identify the command that saves the configuration stored in RAM to NVRAM? A.) copy running-config startup-config B.) copy tftp running-config C.) copy startup running D.) copy active to backup
1 4718Identify the command that displays the SAP table? A.) show ipx servers B.) display SAP table C.) display SAP's D.) show sap table
1 4749
What is the difference between rip and igrp?
What are the types of communication in ipv6 ?
What are the different types of passwords that you can use in cisco routers?
what command you must use if you want to delete or remove the configuration data that is stored in the NVRAM?
Tell us the name of algorithm of eigrp protocol?
Which command we use for ping in ipv6?
Which peer authentication method and which ipsec mode is used to connect to the branch locations?
If line up, but protocol down which layer should be troubleshot?
Tell me when we use standard access-list?
What is the mesh network?
Explain why is udp lease favored when compared to tcp?
Brielfly explain the conversion steps in data encapsulation
What command do we give if router ios is stucked?
How much hold down time of eigrep protocol?
What cable called v.35?
